Sea-air flux of CO2 in the Caribbean Sea estimated using in situ and remote sensing data

Empirical relationships between sea surface carbon dioxide fugacity (fCO₂^sw) and sea surface temperature (SST) were applied to datasets of remotely sensed SST to create fCO₂^sw fields in the Caribbean Sea. SST datasets from different sensors were used, as well as the SST fields created by optimum interpolation of bias corrected AVHRR data. Empirical relationships were derived using shipboard fCO₂^sw data, in situ SST data, and SST data from the remote sensing platforms. The results show that the application of a relationship based on shipboard SST data, on fields of remotely sensed SST yields biased fCO₂^sw values. This bias is reduced if the fCO₂^sw-SST relationships are derived using the same SST data that are used to create the SST fields. The fCO₂^sw fields found to best reproduce observed fCO₂^sw are used in combination with wind speed data from QuikSCAT to create weekly maps of the sea-air CO₂ flux in the Caribbean Sea in 2002. The region to the SW of Cuba was a source of CO₂ to the atmosphere throughout 2002, and the region to the NE was a sink during winter and spring and a source during summer and fall. The net uptake of CO₂ in the region was doubled when potential skin layer effects on fCO₂^sw were taken into account.     

羟基磷灰石涂层人工关节的应用研究

采用人工合成高纯度的羟基磷灰石粉末，喷涂在具有注册证的钛合金和钴铬钼合金人工关节上。通过生物学基础检测、动物实验和临床试用，证明所制作的各种羟基磷灰石涂层人工关节，能诱发骨质生长，起生物固定作用，对治疗丧失功能的骨胳效果甚佳。     

Boiling: Size Distribution of Bubbles as Demanded by the Principle of Maximum Information

The principle of maximum informational entropy is used to find the probability density function for the departure radius of a bubble in boiling on a solid surface. A general relation is derived, which leads to particular expressions.     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

Analysis of the Ductile Strength of Welds Weakened by Notches in Longitudinally Welded Pipes of Large Diameter by the Method of Slip Lines

We study the stressed state of an inhomogeneous welded joint containing an interlayer of a more high-strength material under the action of tensile loads. It is assumed that the contact boundary has a cracklike defect. We deduce analytic dependences of the fracture load on the mechanical inhomogeneity of the joint, thickness of the interlayer, and depth of the defect. The maximum depth of the defect to which the joint is insensitive is established. The proposed theoretical results are innovative and agree with the experimental data obtained for specimens cut out from a pipe of 14KhGS steel.     

The Influence of Surfactant on the Surface Characterization of Celestite in Spherical Oil Agglomeration

This study investigates the relationship between the critical surface tension of wetting of celestite and agglomeration recovery as well as the zeta potential in dependence of pH and amount of collector (Na‐Oleate). For this purpose, effects of pH and collector amount on the agglomeration recovery are investigated and zeta potential measurements and Fourier Transform Infrared Spectrophotometer (FTIR) analyses are carried out to determine the adsorption type of Na‐Oleate on celestite surface. The sessile drop technique is used for the measurement of contact angle and determination of the critical surface tension of wetting (Y_C) of celestite. The maximum agglomeration recovery is obtained at pH 7. The critical surface tension of wetting of celestite is very close to the surface tension of kerosene, which is 25.95 mN/m. Furthermore, at the optimum Na‐Oleate amount of 10 kg/ton, the critical surface tension of wetting of celestite is approximately equal to the surface tension of kerosene.     

Coupling of free surface and groundwater flows

In this paper we present some preliminary results about the coupling of shallow water equations for free surface flows and Darcy equation for groundwater flows. A suitable set of interface conditions is discussed: the Beavers and Joseph formula for the bottom stress is used. An iterative algorithm to solve the coupled problem is proposed and some numerical results are presented.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Damage mechanism in weldment of 2.25Cr-1Mo steel under creep-fatigue loading

The purpose of this study is to clarify damage process of “Type IV cracking” in weldment of a 2.25Cr-1Mo steel and to propose a micro damage prediction method. From continuous observation under a creep-fatigue test, it was found that spherical shape voids initiated and grew on grain boundaries in fine grain region and these voids grow continuously by changing their shape to crack-like. Both spherical and crack-like void growth rate equations were derived from the proposed void growth model. It was indicated that measured void growth rate under the creep-fatigue loading was well predicted by the growth rate equations.     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.