考虑应力历史的饱和黏土一维固结渗透试验研究

为研究固结应力比和应力历史对饱和黏土一维固结渗透的影响,利用GDS三轴仪进行了一系列一维固结-渗透联合试验。研究结果表明,在不同固结应力比相同应力历史条件下,正常固结和超固结饱和黏土在一维固结渗透过程中试样的渗透系数和孔隙比均随固结应力比的增大而减小,试样的最终压缩量均随固结应力比的增大而增大。在相同固结应力比不同应力历史条件下,超固结饱和黏土的最终压缩量小于正常固结饱和黏土。将固结应力σ与土层自重应力σcz的差值σdv与试样最终压缩量sf进行拟合,得出应力差值σdv与各固结应力下的最终压缩量sf间呈良好的线性关系。通过研究发现,同时考虑固结应力比和应力历史对饱和黏土一维固结渗透的影响是有必要的,同时在得到土体自重应力后可较为准确地预测土体最终压缩量。     

A Novel Volume-Stable Collagen Matrix Induces Changes in the Behavior of Primary Human Oral Fibroblasts,Periodontal Ligament,and Endothelial Cells

The aim of the present study was to investigate the influence of a novel volume-stable collagen matrix (vCM) on early wound healing events including cellular migration and adhesion, protein adsorption and release, and the dynamics of the hemostatic system. For this purpose, we utilized transwell migration and crystal violet adhesion assays, ELISAs for quantification of adsorbed and released from the matrix growth factors, and qRT-PCR for quantification of gene expression in cells grown on the matrix. Our results demonstrated that primary human oral fibroblasts, periodontal ligament, and endothelial cells exhibited increased migration toward vCM compared to control cells that migrated in the absence of the matrix. Cellular adhesive properties on vCM were significantly increased compared to controls. Growth factors TGF-β1, PDGF-BB, FGF-2, and GDF-5 were adsorbed on vCM with great efficiency and continuously delivered in the medium after an initial burst release within hours. We observed statistically significant upregulation of genes encoding the antifibrinolytic thrombomodulin, plasminogen activator inhibitor type 1, thrombospondin 1, and thromboplastin, as well as strong downregulation of genes encoding the profibrinolytic tissue plasminogen activator, urokinase-type plasminogen activator, its receptor, and the matrix metalloproteinase 14 in cells grown on vCM. As a general trend, the stimulatory effect of the vCM on the expression of antifibrinolytic genes was synergistically enhanced by TGF-β1, PDGF-BB, or FGF-2, whereas the strong inhibitory effect of the vCM on the expression of profibrinolytic genes was reversed by PDGF-BB, FGF-2, or GDF-5. Taken together, our data strongly support the effect of the novel vCM on fibrin clot stabilization and coagulation/fibrinolysis equilibrium, thus facilitating progression to the next stages of the soft tissue healing process.     

Micron-Scale Soft Actuators Fabricated from Multi-Shell Polystyrene Particle-Gold Nanoparticle Nanohybrids

Actuators made of soft matter are needed for a variety of fields ranging from biomedical devices to soft robotics to microelectromechanical systems. While there are a variety of excellent methods of soft actuation known, the field is still an area of intense research activity as new niches and needs emerge with new technology development. Here, a soft actuation system is described, based on a core-multi-shell particle, which moves via photothermal expansion. The system consists of a novel polystyrene-based thermally expandable microsphere, with a secondary shell of a silicate-silane graft copolymer, to which gold nanoparticles are covalently linked. The gold nanoparticles act as photothermal nano-transducers, converting light energy into the thermal energy necessary for microsphere expansion, which in turn results in material movement. Actuation is shown in isolated particles in thermal and photothermal regimes using metal ceramic heaters or 520 nm laser illumination, respectively. Macroscale actuation is demonstrated by making a composite material of particles suspended in the transparent elastomer polydimethylsiloxane. The sample demonstrates an inchworm-like movement by starting from an arched geometry. Overall, this work describes a new particle-based actuation method for soft materials, and demonstrates its utility in driving the movement of a composite elastomer.     

LF软吹时间对硅脱氧弹簧钢氧化物夹杂控制影响

 对于一些采用硅锰脱氧冶炼工艺的特殊钢,为保证钢水洁净度,常会选择较长时间的LF软吹处理,导致过程能耗增加。通过工业试验,借助FEI Explorer 4自动扫描电镜检测,研究不同LF精炼软吹时间对硅脱氧弹簧钢55SiCr铸坯氧化物夹杂成分、数量的影响;并采用夹杂物极值统计法,对比评价不同LF精炼软吹时间对应成品盘条横截面最大夹杂物尺寸控制情况。结果表明,在LF软吹10 min与软吹40 min 两种工艺条件下,铸坯中尺寸大于5 μm的氧化物夹杂成分接近,均在CaO-SiO₂-Al₂O₃相图中假硅灰石、钙长石和钙铝黄长石共晶低熔点区,其中软吹10 min工艺铸坯氧化物夹杂组成落入低熔点区的数量所占比例更大。LF软吹10 min与软吹40 min铸坯中尺寸大于5 μm的氧化物夹杂数量密度分别为11.70个/100 mm2和14.59个/100 mm2,尺寸大于15 μm 的氧化物夹杂数量密度分别为0.53个/100 mm2和1.65个/100 mm2,LF软吹10 min工艺铸坯大尺寸氧化物夹杂数量密度略低于LF软吹40 min工艺。当预测面积为30 000 mm2时,两种LF软吹时间对应成品盘条横截面最大夹杂物尺寸分别为27.1 μm和28.1 μm,盘条最大夹杂物尺寸控制无显著差别。结合硅锰脱氧钢中大尺寸低熔点CaO-SiO₂-Al₂O₃系夹杂物主要源自钢包渣乳化卷入,具有与钢水和氩气泡界面接触角很小、难以通过吹氩上浮去除的特点,建议硅锰脱氧钢LF软吹过程按短时间快节奏进行控制。     

Mo的替代对FeNbBCu软磁纳米晶合金磁谱的影响

本文研究了Fe82Nb7-xMoxB10Cu1(x=0,1,3,5）系列纲伙晶软磁合金中Mo的含量对磁导率谱（频率范围1kHz-1MHz)的影响，并用畴壁钉扎理论进行了解释，在磁谱中观测到随着Mo含量的增加，弛豫频率线性地上升，μ′随外加磁场幅度变化曲线表明其原因在于Mo的替代导致了钉扎场的增强。     

CHARACTERISTICS OF INTERNAL FRICTION AND MODULUS ASSOCIATED WITH NON-EQUILIBRIUM DIFFUSION-TYPE PHASE TRANSFORMATION IN EUTECTOID Al-Zn ALLOY

The characteristics of the low frequency internal friction and the modulus effect associatedwith the non-equilibrium spinodal pretransformation and the following discontinuous trans-formation was investigated in an as-quenched eutectiod Al-Zn alloy.It was observed that theloss of the stability in the lattice,which corresponded to the large-amplitude long-wavelengthstatic concentration wave in the non-equilibrium spinodal pretransformation,did not induceany effect of localized soft modulus.Although there are two aging internal friction peaks inphase transformation which correspond to the appearance and disappearance of the coherencyin spinodal pretransformation and the maximum of the interface area in the discontinuoustransformation respectively,the effect of localized soft modulus did not take place yet.     

基于PC的开放式软PLC技术

本文讨论了开放式软PLC(softPLC)的性能特点和组成结构,比较了软PLC与传统PLC技术的异同点,分析了软PLC技术在工业控制领域的实现方案,最后阐述了它的前景及发展趋势。     

铜离子注入Ti6Al7Nb合金的表面改性研究

使用MEVVA强流金属源离子注入机对Ti6Al7Nb合金表面注入能量为80keV、剂量分别为0.5×1017,1×1017,2×1017,4×1017ions/cm2的铜离子,计算得到铜离子饱和注入量为2.15×1017ions/cm2。研究了注入的铜离子对Ti6Al7Nb合金腐蚀性能、显微硬度和磨损行为的影响,采用覆膜法研究了铜离子注入后试样对金黄色葡萄球菌的抗菌性能,并分析了注入剂量与抗菌性能的关系。结果表明,Ti6Al7Nb合金的硬度和耐磨性随着注入剂量的增加而提高,点蚀电位随着注入剂量的提高而下降。抗菌试验显示当注入量达到饱和注入量时,试样的抗菌率达到99%以上。     

软包装标牌模具的设计和加工

分析了零件的工艺特点 ,介绍了此类软包装高速冲模的结构 ,以及模具中的计数装置、凸模上吹气卸料和收料装置 ,并对该模具的加工工艺做了详细的介绍     

软段含羧基的水性聚氨酯贮存稳定性研究

合成了软段含羟基的水性聚氨酯（WPU），对影响其贮存稳定性的各种因素进行了研究，通过显微镜对PU进行了观察。结果表明：以甲苯二异氰酸酯（TDI）合成，在有性溶剂（如丁酮、丙酮）条件下用三乙胺中和，采用较小相地分子质量的聚酯有利于增强WPU的贮存稳定性，以TDI合成的PU-TDI体系的粒径较PU-IPDI体系的小，稳定性高；以丁酮、丙酮为溶剂的PU-IPDI体系相反转完全。