水驱强度对油井压力动态的影响研究

建立了水驱强度影响下的水驱油渗流数学模型，在获得数学模型解的基础上，计算了考虑井筒储存、表皮效应以及水驱强度影响下油井的压力及压力导数典型曲线，分析了压力动态特征，通过这些研究为水驱油藏的试井分析提供了理论基础，为水驱油藏的识别提供了一种新的手段。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Characterization of strength properties of thin polycrystalline silicon films for MEMS applications

The aim of this work is to characterize the strength properties of polycrystalline silicon (polysilicon) with the use of tensile and bending test specimens. The strength of thin polysilicon films with different geometry, size and stress concentrations has been measured and correlated with the effective size of the specimen and its stress distribution. The test results are evaluated using a probabilistic strength approach based on the weakest link theory with the use of STAU software. The use of statistic methods of strength prediction of polysilicon test structures with a complex geometry and loading based on test values for standard material tests specimen has been evaluated.     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

Case Study-Based Challenges of Quality Concrete Finishing for Architecturally Complex Structures

This paper focuses on the procedure utilized in the construction of tilt-up irregular concrete panels that are constructed on-site using concrete slabs and wooden formwork. The case study required high-quality concrete finishing. The erection and installation procedure called for a maximum panel-to-panel joint tolerance of 1.27?cm (0.5?in.), often 90° joints between panels. To meet precision requirements, the casting slabs were leveled and flattened with laser screed technology and smoothed with chemical solutions. To ensure that the final result met expectations, a mock-up model was built using different types of materials and to simulate site constraints. The architectural design is a composition of precast concrete panels like “Lego” pieces assembled similarly to a jigsaw puzzle. The unique construction process required a state-of-the-art analysis to produce the set quality. Quality conditions as set by the owner included creating a smooth concrete surface on all panels while avoiding damages and reducing equipment and material costs. The proposed methodology is described through its implementation on the case study, which is also described in this paper.     

Express Method for Estimation of Tensile Strength and Crack Resistance of Brittle Media

The procedure is proposed for estimating the crack resistance and tensile strength of rocks by the results of experiments on disk samples with holes. The gradient approach to the strength problem is employed in processing the experimental data.     

Al_(10)Zn_(2.9)Mg_(1.7)Cu超高强铝合金的喷射成形制备研究

采用喷射成形技术制备了Al1 0 Zn2 .9Mg1 .7Cu高强高韧铝合金沉积坯件 ,研究了喷射成形制备过程中各工艺参数对沉积坯件的成形性、显微组织、致密度的影响 ,确定了适当的工艺参数 ,研究了沉积坯件的热挤压及热处理工艺 ,对材料的组织进行了分析并对不同状态的材料性能进行了比较。研究结果表明 :当喷射成形工艺参数合理时 ,沉积坯件具有良好的成形性与致密度 ,在随后的热挤压过程中 ,通过较低的挤压比即可使材料达到全致密 ;通过对合金进行适当的热处理 ,材料的极限抗拉强度达到 810MPa ,同时延伸率保持在 8%～ 11% ,该材料是一种理想的轻质高强结构材料。     

Determination of shear strength values according to EN 408

This paper presents the results of 382 shear tests carried out according to EN 408. The test pieces consisted of spruce (Picea abies) and varied in density and ring width orientation (radial, tangential and at an angle of 45° to the steel plates). In addition pieces containing pith and knots were tested. The paper discusses problems observed when using this test configuration and shows that the test results do not support the characteristic shear strength values as given in EN 338. Moreover, the test results do not support the relationship between characteristic shear strength and characteristic bending strength as given in EN 384.

---

Résumé Cet article présente les résultats de 382 essais de cisaillement menés conformément à EN 408. Les éprouvettes d’essai sont en épicéa (Picea abies) et présentent une variabilité en termes de masse volumique et d’orientation des cernes d’accroissement (radiale, tangentielle, à un angle de 45° par rapport aux plaques métalliques). Des éprouvettes supplémentaires contenant du cœur et des nœuds ont également été testées. L’article évoque les problèmes qui ont été mis en évidence lors de l’utilisation de ce dispositif expérimental et montre que les résultats expérimentaux ne sont pas en accord avec les valeurs caractéristiques de résistance au cisaillement données dans EN 338. De plus, ces résultats ne confirment pas la relation entre résistance caractéristique au cisaillement et résistance caractéristique à la flexion telle que stipulée dans EN 384.

     

Mechanism and Optimal Application of Chemical Additives for Accelerating Early Strength of Lime-flyash Stabilized Soils

1IntroductionLime-flyashstabilizedsoil as a semi-rigid base mate-rial in highwayis widely usedin China.The goodintegri-ty,great bearing capacity,highstiffness and water-proof-ing quality areits special advantages.But itsinherent lowearly strength makes it…