Numerical simulations of specimen size and mismatch effects in ductile crack growth - Part II: Near-tip stress fields

The effect of ductile crack growth on the near tip stress field in two different specimen geometries has been investigated. For homogeneous specimens it is observed that the peak stress level increases with ductile crack growth. The effect is most pronounced up to about 1 mm of crack growth. For low and intermediate hardening there is a significant effect of specimen size on the stress level. In case of mismatch in yield stress, the simulations show that the increase in stress level in the material with the lower yield stress is of a similar magnitude as is the case for stationary cracks. In case of ductile crack growth deviation from the original crack plane occurs, the highest stresses are still found close to the interface, and not in front of the current crack tip.     

A comparative study of numerical solutions to non-linear discrete crack modelling of concrete beams involving sharp snap-back

Numerical problems are often encountered in modelling crack propagation in concrete beams using non-linear finite element (FE) analysis, especially when sharp snap-back behaviour in load-displacement relations occurs. This paper firstly identifies 16 arc-length control based numerical strategies based on extensive literature review. They are then used to carefully model the structural behaviour of a four-point single notched shear beam using discrete crack modelling approach in which cracks are represented by interface elements with bilinear softening constitutive laws. Based on extensive FE analyses, detailed comparisons of the merits and demerits of these numerical algorithms are then made. The results indicate that the effectiveness and efficiency of different algorithms may vary considerably from one to another, with the local arc-length based procedures in conjunction with tangential stiffness strategy and reversible unloading model being the most robust.     

广州中信商城地下连续墙施工工艺

本文介绍了广州中信商城地下连续墙的施工工艺。该工艺采用膨润土制浆配制方式，施工质量高，效果好。     

混凝土结构的质量通病——裂缝

从材料、结构构造、施工工艺、地基变形、温湿度变形等方面论述了混凝土裂缝产生的原因 ,提出只有真正了解裂缝产生的原因 ,才能有针对性地采取有效措施 ,确保工程质量     

高层地下室底板混凝土施工的裂缝控制

以德益花园写字公寓楼地下室底板205m厚混凝土的施工工程为例，坚持预防为主的原则，采取了一系列温控技术措施，有效地防止或控制了温度裂缝(收缩裂缝)的产生，确保了混凝土的施工质量。     

碾压混凝土抗裂性能的几个影响因素研究

影响碾压混凝土抗裂性能的因素很多，本文主要从水泥矿物成分、石粉含量、掺和料（氧化镁等）、骨料特性（弹性模量）及砂率等方面影响因素开展试验研究，分析各因素对碾压混凝土抗裂性能的影响效果。试验结果表明，砂率和石粉含量均存在碾压混凝土抗裂能力最大的最优含量；掺入适量的氧化镁掺和料和合理增加水泥熟料中的C，S和C4AF两种矿物成分含量，对提高碾压混凝土的抗裂能力非常有利；骨料的弹性模量是影响混凝土弹性模量的重要因素，使用低弹性模量骨料可以大大降低混凝土的弹性模量，增大极限拉伸值，提高混凝土的抗裂能力。     

简析Ⅲ类PHC管桩的成因及加固补强处理方法

本文主要通过Ⅲ类PHC管桩的形成分析,经过各方论证采用了合适的处理方法,取得了较好的效果。     

浅析露天栈桥改造

结合工程实例，论述了露天栈桥产生裂缝和腐蚀的原因，对栈桥结构进行了评价，提出了加固方案及加固施工中应注意的事项，经使用证明，加固效果良好。     

街面水电站混凝土面板堆石坝主要技术问题探讨

街面水电站拦河坝为混凝土面板堆石坝,在面板止水结构型式、面板防裂措施、上游面的施工方法、趾板开挖处理及趾板灌浆等方面,根据工程实际情况,结合国内外的新技术新工艺进行了探讨。     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.