马钢直弧型板坯连铸机的设计

介绍了马钢 2 5 0 mm× 1 40 0 mm直弧型坯连铸机设计指导思想、连铸机主要技术性能指标、工艺流程、设备组成及采取的技术措施 :无氧化浇注 ,连续弯曲矫直 ,二冷区气雾冷却及自动控制 ,在线短定尺二次切割 ,对称式双向出坯 ,防止测量基准移位和台阶式对弧样板等。     

电弧钎焊技术的应用及发展

阐述了TIG钎焊和MIG钎焊两种方法的工作原理及特点,比较了这两种焊接方法的异同,介绍了其焊接工艺过程和注意事项;详细介绍了电弧钎焊技术在国内外的发展历史,许多国家都已经对其进行了深入的研究,焊接工作者已经研制成功了电弧钎焊专用焊丝、焊机等;针对电弧钎焊具有硬钎焊和熔化焊的双重特点,对比分析了电弧钎焊与电弧焊和钎焊的异同,探讨了其应用领域和发展前景,在汽车业镀锌钢板连接、薄壁件生产以及异种材料连接上得到了广泛应用.电弧钎焊技术已经成为一种高效实用的焊接技术,将会得到更为广泛的应用.     

压力容器环缝焊接自动跟踪系统的研究

作者研制了一种新型摆动式电弧传感器及其焊缝自动跟踪系统。采用计算机控制，成功地应用于压力容器的环缝脉冲ＭＡＧ焊工艺。实践证明采用这种系统跟踪精度高并获得了优质焊缝。     

埋弧自动焊在大口径钢卷管焊接上的应用

为把埋弧焊应用在大口径钢卷管焊接上,分析了焊接工艺设计、焊接工装设计和纵缝、环缝焊接的施工要点,经过实际施工验证了这种方法是成功的,效益是高的。     

A novel arc welding inverter with unit power factor based on DSP control

A novel inverter power source is developed characterized with constant output current and unit power factor input. Digital signal processor （ DSP ） is used to realize power factor correction and control of back-stage inverter bridge of the arc welding inverter. The fore-stage adopts double closed loop proportion and integration （PI） rectifier technique and the back- stage adopts digital pulse width modulation （ PWM） technique. Simulated waves can be obtained in Matlab/Simulink and validated by experiments. Experiments of the prototype showed that the total harmonic distortion （THD） can be controlled within 10% and the power factor is approximate to 1.     

海洋平台大厚度焊接接头断裂韧度

依据BS7448断裂韧度试验标准(ISO／TC164／SC4-N400)，对采用埋弧焊(SAW)工艺施焊的、板厚为54mm的海洋石油平台大厚度对接接头试样进行了低温裂纹尖端张开位移(CTOD)试验。分别测试了-15℃下单丝和双丝埋弧焊工艺下焊缝金属和热影响区的CTOD值。试验表明，除双丝埋弧焊热影响区试件外，其余试件均满足挪威船级社DNV规定的最小特征CTOD为0．15mm的要求，为指导海洋平台的施工建造提供了科学依据。     

Thermal stability behaviors of Cr(N,O)/CrN double-layered coatings by TGA/DTA analysis

In this study, Cr(N,O)/CrN double-layered coatings were synthesized using the cathodic arc deposition (CAD) process. CrN film was first deposited onto a substrate as an interlayer to ensure better adhesion, and Cr(N,O) film was subsequently deposited on top of the CrN layer as the surface layer. Variation in the Cr(N,O) coating composition was achieved through changing the O₂/N₂ flow ratio during the last stage of processing. Phase structure, chemical composition, and morphology of the resulting coatings were analyzed and observed using the X-ray diffractometer, Auger electron spectrometer and SEM. In addition, oxidation behavior of the coatings was investigated using TGA/DTA methods. The tests were carried out by increasing temperature up to 1000 °C in ambient air. With the introduction of oxygen gas during the CAD process, a superficial layer was produced in the Cr(N,O) constituent containing CrN and Cr₂O₃ phases. The formation of the oxide phase attributed to the reaction of chromium and oxygen was more favorable than that of chromium and nitrogen. The results also showed that Cr(N,O)/CrN double-layered coatings exhibited superior oxidation resistance at elevated temperature than that of CrN single-layer coated specimen (870 °C vs. 750 °C).     

用GA-BP算法研究超音速电弧喷涂JCW-S-AM涂层显微硬度与工艺参数间的关系

采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW-S-AM涂层,利用显微硬度计测定各种涂层的显微硬度.根据测试结果,运用GA-BP算法构建涂层显微硬度与喷涂电压、喷涂电流的关系模型并进行工艺参数优化.研究结果表明:喷涂电压和喷涂电流对涂层显微硬度均有影响,呈现非线性规律,并且电压和电流之间存在交互作用;通过遗传算法优化,获得的最佳喷涂工艺参数为:喷涂电压29V,电流200A.此时JCW-S-AM涂层显微硬度最大.     

X80管线钢埋弧焊匹配焊丝试验

通过分析高强度低合金钢焊缝熔敷金属常见显微组织对其力学性能的影响,确定X80管线钢用埋弧焊丝熔敷金属组织应以大量针状铁素体(AF)和少量粒状贝氏体(GB)的复合组织.从相变动力学原理出发,结合针状铁素体(AF)非自发形核机制和微合金组织韧化理论,选择Mn-Ni-Mo-Ti-B合金系进行X80管线钢匹配焊丝的试制.结果表明,合理选择和控制合金元素,可以获得理想的焊缝熔敷金属组织和强韧性以及低温韧性要求,试制的1号焊丝能够满足X80管线钢的使用要求.     

液压-齿轮-齿条圆弧分型抽芯压铸模设计

给出了龙头体液压-齿轮-齿条圆弧分型抽芯压铸模实用结构，论述了模具的浇铸系统、结构特点和工作原理。该模具采用扇形龄轮-齿条机构实现龙头体铸件的侧向圆弧分型抽芯，同时通过相应的两套斜销滑块机构分别实现龙头体铸件另外两个方向的侧向分型抽芯。