泄压注浆法在治理小型突水中的运用

七煤集团建设工程公司在施工辽阳铧子石膏矿主、风井井筒时 ,多次采用泄压注浆法成功通过中小型含水层 ,对小型突水进行了有效封堵 ,取得了较好的经济效益     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

确定异常高压气藏地质储量和可采储量的新方法

基于文献[1]的定容，封闭，异常高压气藏的物质平衡方程式，提出了确定异常高压气藏原始地质储量，可采储量和采收率的新方法，通过实例的应用和对比表明，提供的新方法是适用的有效的。     

Application of a Compaction Simulator to the Design of a High-Dose Tablet Formulation. Part I

The compaction properties of an investigational drug are studied by the use of a compaction simulator. The effects of punch velocity over the range of 30-640 mm^-1 on the compaction properties of the pure drug and a variety of formulas incorporating a high dose of the active compound have been investigated. The data were analyzed by applying the Heckel equation. The pure drug was found to have a high yield pressure at a relatively low punch velocity of 31 mm^-1. As the punch velocity was increased there was a decrease in crushing strength, primarily as a result of increasing yield pressure. These findings indicate that the pure drug predominantly consolidated by fragmentation and elastic deformation, with a slow plastically deforming component. The information obtained on the consolidation mechanism of the pure drug and, subsequently, on model formulas were instrumental in the design and selection of a robust formula and granulation process. The advantages of conducting dosage form design and characterization studies during the early phase of tablet formulation using means such as a compaction simulator are emphasized in this investigation.     

Processing and properties of zirconia-toughened alumina ceramics

Al₂O₃:ZrO₂ ceramics have been prepared from physically mixed pure oxide powders. The results indicate that careful processing of the starting powders and a two-stage sintering process can avoid expensive processing methods like hot pressing/hot isostatic pressing used for achieving high densification. The mechanical properties were measured and the resultant microstructure studied to explain the toughening behaviour of this material.     

超高增压柴油机与斯特林发动机复合运行的分析

本文对超高增压柴油机与斯特林发动机的复合运行进行了初步的探讨,陈述了这种复合运行作为未来发动机技术发展方向之一的可能性。     

压力对Fe－29wt％Ni合金超细微粒特性的影响

利用蒸发冷凝法，制备了不同平均粒径的Ｆｅ－２９ｗｔ％Ｎｉ合金超细微粒。在不同压强下，将超细微粒压制成片。随压强增大，马氏体体积分数和比饱和磁化强度σｓ明显增大，而矫顽力Ｈｃ呈线性下降。压力效应与平均粒径ｄ大小密切相关     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

刮板输送机接链用千斤拉的研究

针对刮板输送机的掐链、接链问题,研制出新型掐、接链用千斤拉,介绍了该装置的结构特点和工作原理,并对使用效果进行了分析。     

中压甲铵冷凝器防结垢方法探讨

分析中压甲铵冷凝器的工艺流程和操作条件，指出设计中的不足，找出其结垢的非药剂因素——温度和流速，对一些相关改造的成败提出观点，并提出增设加压泵回流控温和增大上、回水压差的新思路。