高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

Modelling of Diffuse Interfaces with Temperature Gradients

The work is devoted to capillary phenomena in miscible liquids under the assumption that they have a constant and the same density. The model consists of the heat equation, diffusion equation, and the Navier-Stokes equations with the Korteweg stress. We study several configurations corresponding to the microgravity experiments planned for the International Space Station. The basic conclusion of the numerical simulations is that transient capillary phenomena in miscible liquids exist and can produce convective flows sufficiently strong to be observed experimentally. In particular, there exists a miscible analogue to the Marangoni convection where the temperature gradient is applied along the transition zone between two fluids. Convection also appears if, instead of the temperature gradient, the case where the width of the transition zone varies in space is considered. Finally, similar to the immiscible case, miscible drops move in a temperature gradient.     

Perceived stress management skill mediates the relationship between optimism and positive mood following radical prostatectomy.

This study evaluated relations among optimism, perceived stress management skills (PSMS), and positive mood in 46 men who had surgical treatment for localized prostate cancer. The authors found that optimism, PSMS, and positive mood scores were positively correlated. Positive mood was unrelated to demographic and disease-related control variables. In a hierarchical regression model controlling for PSMS, the relationship between optimism and positive mood became nonsignificant, whereas PSMS remained a correlate of positive mood. Results suggest that the relationship between optimism and positive mood may be mediated by belief in being able to use stress management techniques effectively. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

Preparation and Compressive Stress Effect of Polymer Matrix RE-Fe Giant Magnetostrictive Composite

Polymer matrix RE-Fe giant magnetostrictire composite （GMPC） was prepared using bonding and magnetic field forming technique, and magnetostriction of samples was measured for different compressive stress. The experimental results show thai there is certain compressive effect in GMPC. And the influence of compressive stress on magnetostriction of sample was investigated. It offers essential reference for application and device design of GMPC.     

The five elements and chinese-american mortality.

D. P. Phillips, T. E. Ruth, and L. M. Wagner (1993) reported that 1969-1990 California mortality data show that Chinese Americans are particularly vulnerable to diseases that Chinese astrology and traditional Chinese medicine associate with their birth years. For example, because fire is associated with the heart, a Chinese person born in a fire year (such as 1937) is more likely to die of heart disease than is a Chinese person born in a nonfire year. However, many diseases were excluded from this study, some diseases that were included have ambiguous links to birth years, and the statistical tests were indirect. A more complete statistical analysis and independent California mortality data for the years 1960-1968 and 1991-2002 did not replicate the original results. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

工程钻机在沙卵石地区的物探钻井

川西平原属沉积平原，不到2m厚的表土下面全是沙卵石，沙卯石厚度达二、三十米。地面覆盖农田，沟垄纵横，限制了车载钻机的进入。以往地震勘探多采取浅井组合方式激发，所获得的地震资料能量差、面波强，对农田破坏面积大。若使用SH30—2A型轻便工程钻机，配上自制的冲击管，采取冲击钻进，从管中下药柱的方式，可实现沙卵石地区的深井激发，提高资料采集质量，且效率高、成本低。