焦化厂门型吊改造

从门型吊承轨梁的受力分析入手．研究剖析了原结构产生裂纹的诸多原因．通过理论计算。做出了承轨梁与桁架连接接点的最佳设计．提出了符合现场实际情况的更换承轨梁的最佳方案，为类似设备改造提供了可借鉴的经验。     

Numerical simulation of slider dynamics during slider–disk contact

In this paper, the dynamic behavior of pico slider in contact with the disk was calculated. The analysis model consists of a simplified suspension model, an air bearing model, and a slider–disk contact model. The contact model consists of two elements. One is surface roughness model measured by Atomic Force Microscope (AFM) and the other is micro-waviness model. The dynamic behaviors of the tri-pad slider are calculated at several rotation speeds to investigate slider vibration modes during slider–disk contact. The slider oscillation frequency depends on the rotation speed and it saturates about twice as much as eigen frequency of air bearing pitch mode.     

基于小波包和包络分析的滚动轴承故障自动诊断方法

提出了一种基于峭度-小波包-包络分析的滚动轴承故障自动诊断方法。首先用峭度系数判断是否出现故障,再针对故障轴承振动信号非平稳和调幅的特点,用小波包将信号分解到不同的节点上。然后将不同节点的重构信号做包络谱分析,将谱峰处的频率同滚动轴承内圈、外圈、滚珠、保持架等的故障频率进行对比分析,在此基础上,运用最小距离判别法则自动获得故障原因,从而实现滚动轴承故障的自动诊断。通过对实验中采集到的轴承振动信号进行分析,证明了该方法在轴承早期故障诊断中的有效性。     

空调压缩机用冲压外圈滚针轴承

着重分析空调压缩机采用新的环保型冷媒体后，常规结构滚针轴承的破坏情况，提出了冲压滚针轴承新的结构改进设计及其开发和性能比较结果，为今后新冷媒体空调压缩机的广泛使用，提供了有利的保证。     

连轧管机轧辊轴承的调整、维护及保养

本文介绍了应用于MPM连轧机轧辊上的四列圆锥滚子轴承的结构特性及其调整、维护、保养，旨在提高轴承的使用寿命。     

聚脲基脂及其在电机轴承上的应用

对电机轴承专用聚脲基脂的特点及其在电机轴承上的应用效果进行了分析和探讨。正确使用电机用润滑脂是保证电机正常工作，减少电机故障的关键措施之一。采用电机专用聚脲基脂后，电机轴承工作温度明显下降，电机故障率明显减少。     

福州洪山大桥支座整体更换施工的方法和措施

本文针对国道316线福州洪山大桥支座整体更换工作中所采用的主要施工方法和措施进行介绍,对类似桥梁的养护工作具有指导意义。     

电加热井的井筒温度场数学模型

运用传热学理论，通过对稠油从井底流出井筒的温度变化、井筒原油与地层之间热交换过程的传热机理研究，建立数学模型，可以模拟不同产量、不同含水的井筒温度剖面，以及电加热所需功率，从而为稠油井电加热生产方案的制定提供科学依据。     

数控母排冲孔机液压系统

介绍了数控母排冲孔机液压系统工作原理及其组成，设计了双泵供油回路、压力控制的差动快进转慢进回路及过载、过热、污染堵塞报警系统。     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.