氧化锌颗粒膜电阻响应-恢复特性研究

测试了氧化锌颗粒膜电阻响应-恢复特性，讨论了颗粒形态，加热电压、环境气氛、气氛浓度和注入方式等因素对电阻响应-恢复特性的影响。结果表明，随着加热电压的升高，电阻响应-恢复的速度和程度明显加大；断续注入时颗粒膜电阻值的响应随着浓度的增加逐步减弱．     

Influence of the deposition atmosphere on the characteristics of Pd–Mg thin films prepared by pulsed laser deposition

Bilayered palladium (30 nm thick)–magnesium (350 nm thick) thin films were prepared using the pulsed laser deposition technique in the presence of various background gases (Ar, He and a mixture He + H₂) under different partial pressures (47 and 27 Pa). According to the deposition atmosphere, the Pd/Mg interface shows either a sharp or an extended transition. The electrochemical hydriding properties and the mechanical stability upon cycling of the Pd/Mg film are greatly improved when an extended «intermixing» zone between the Pd and Mg layers is present. The Pd–Mg films prepared under pure helium fulfill these conditions.     

Thin film deposition on a corrugated surface: A molecular dynamics approach

This paper presents the use of molecular dynamics (MD) simulation in the investigation of the surface topography of early-stage film growth on a GMR (giant-magnetoresistance) corrugated structure. The size of the simulated system is limited in order to reduce the computational workload. The numerical model adopts the Morse potential and the Verlet-leapfrog time evolution scheme [R.W. Hockney, 1970; D. Potter, 1972 (Chapter 5). [1]] to describe the atomic interactions which take place between the atoms. The impact energy transferred from the incident atoms to the substrate is modeled by rescaling the atoms within the upper substrate layers. It is found that the important properties of the film-substrate system may be obtained after the deposition of just several atomic layers. The influence of the impact velocity upon the coating parameters is investigated by varying the incident energy of the deposited atoms. The current results indicate that the surface coverage is poor, when atoms are deposited at low incident energies upon a low temperature substrate. At a higher incident energy, the deposited film tends to exhibit a quasi-layer-by-layer growth mechanism, which results in an improved surface coverage. Finally, it is demonstrated that a distinct quasi-fluid behavior is evident on the substrate when the atoms are deposited at high incident energies.     

基于PTFE的PCB的多层层压方法

介绍了采用不同材料类型的粘结膜、半固化片、所需设备和粘结材料,用于生产低到高层数的PTFE多层板的情况。     

Synthesis and characterization of polyaniline films using Fenton reagent

The chemical oxidation of aniline to form polyaniline (PANI) films and powder samples was made using Fenton reagent as an oxidizing agent in aqueous sulfuric acid medium. The PANI films were monitored by using the quartz crystal microbalance and the electronic absorption techniques. The optimum concentration was determined and the results were justified by measuring the UV–vis absorption spectra for the in situ PANI films. The conductivity for the PANI films and powder samples, prepared in different conditions, was measured. Also, the IR spectra, X‐ray and the thermogravimetric analysis for the PANI powder formed in the bulk were measured and compared with the polymer prepared using ammonium peroxydisulfate. A preliminary investigation to the dielectric properties of the polymer powder was measured and discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

The Strategic Control of Multiple Routes in Imitation of Actions.

The aim of this study was to bring to the surface the strategic use of imitative processes in the context of a 2-route model: (a) direct imitation, used in reproducing new, meaningless actions, and (b) imitation based on stored semantic knowledge of familiar meaningful actions. Three experiments were carried out with healthy participants who reproduced meaningful and meaningless actions within an established time limit. The study investigated 3 factors that could potentially affect the selection of processes used for imitation: (a) the composition of the experimental list (blocked or mixed presentation), (b) the presence-absence of instructions (Experiments 1 and 2), and (c) the relative proportions of the stimuli (Experiment 3). Overall, the results suggest that each of these factors influences the selection of imitative strategies in healthy individuals with temporarily reduced capacities, as happens in the case of brain-damaged patients. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

国产50%离子膜法烧碱蒸发装置及运行情况

介绍了升降膜法双效逆流蒸发生产50%离子膜法烧碱的工艺流程、主要设备、装置特点及运行情况.