Ni的添加对TiB2-CU基复合材料微观组织的影响

利用燃烧合成工艺原位合成了TiB2-Cu基复合材料，为了改善TiB2陶瓷和Cu基体的润湿性，将金属Ni作为合金化元素加入到TiB2-Cu复合材料。通过XRD，SEM，EPMA和TEM等检测手段对金属Ni的添加对TiB2-Cu基复合材料微观组织的影响进行了研究。结果表明，含Ni复合材料的金属粘结相的面间距比不含Ni时Cu的面间距均有不同程度的减小；Ni加入后，TiB2-Cu-Ni复合材料的组织较TiB2-Cu复合材料更加致密，但陶瓷颗粒尺寸却大于TiB2-Cu复合材料的颗粒尺寸；Ni的加入降低了复合材料的导热率和冷却速度，使得部分TiB2陶瓷颗粒有足够的时间长成棒状，同时造成TiB2陶瓷颗粒间形成更多的烧结颈；Ni的加入也改善了陶瓷与金属粘结相之间的润湿性，使陶瓷相与金属粘结相的界面结合牢固，看不到TiB2-Cu复合材料中界面脱开的现象。金属Ni的添加有利于改善TiB2-Cu基复合材料的微观组织，进而利于复合材料的致密化。     

The Amygdala Modulates Hippocampus-Dependent Context Memory Formation and Stores Cue-Shock Associations.

Preexposing rats to the context facilitates subsequent contextual fear conditioning. This effect depends on the hippocampus (J. W. Rudy, R. M. Barrientos, & R. C. O'Reilly, 2002). The authors report that inactivating the basolateral region of the amygdala (BLA) by injecting muscimol, a GABAA agonist, before or after preexposure reduced this effect. In contrast, bilateral injections of anisomycin, a protein synthesis inhibitor, into BLA did not impair the consolidation of the context memory. However, when injected after fear conditioning, anisomycin impaired consolidation of both contextual and auditory-cue fear conditioning. Results are consistent with 2 ideas about the amygdala's contribution to memory: (a) It modulates memory formation in other regions of the brain, and (b) it is a storage site for cue-shock associations. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

雷达仿真系统中电磁干扰环境的仿真设计和实施

雷达仿真系统是为检测雷达设备的抗干扰能力以及在各种电磁环境下的工作性能而设计的，包括有源干扰和无源干扰的模拟仿真。本文阐述了无源干扰即杂波的散射模型和仿真过程；从同步脉冲干扰的基本原理出发，阐明在雷达工作环境仿真系统中距离拖引、速度拖引、虚假目标等同步脉冲有源干扰的设计和实施过程；并针对工作在搜索和跟踪交替模式下的相控阵雷达提出自适应综合干扰方式；最后分析并总结了系统仿真时为真实、有效地模拟电磁干扰环境应注意的关键问题。     

Characterization of ZnS:Cu, Br electroluminescent phosphor prepared by new route

Synthesis of electroluminescent ZnS:Cu, Br phosphor by a number of routes has been presented along with their brightness-voltage, brightness-frequency, brightness-waveform and spectral energy distribution studies. The sample fired in N₂ atmosphere with aluminum and bromine shows predominantly green emission with a peak around 530 nm whereas the sample prepared under H₂S and HBr shows the broadest emission spectrum with multiple peaks. These peaks may arise out of different possible bands of copper, self-activated luminescence of ZnS and association of copper with some of the donor levels formed because of the higher reactivity of HBr. All the samples have been found to obey the relation B=B₀ exp.(−b/V^0.5) which has been discussed using bipolar tunnel emission model. The frequency variation of brightness is linear. Samples containing bromine show multiple secondary peaks indicating that bromine helps in formation of multiple shallow traps.     

Premixed metal fibre burners based on a Pd catalyst

As an alternative to previously developed catalytic FeCrAlloy fibre mat burners based on perovskite catalysts, new catalytic burners have been developed based on Pd catalyst on lantana-stabilised Al₂O₃ and different fibre structures (NIT100A, NIT100S and NIT200S by ACOTECH NV). All development steps are considered, shifting from catalyst preparation (based on combustion synthesis of γ-Al₂O₃) to the optimisation of lantana and Pd loadings, from the definitions of the best catalyst-deposition conditions (washcoating) to the catalytic burners performances, determined in an ad hoc developed combustion chamber. The results show almost half pollutants emissions and better performance compared to various non-catalytic counterparts, especially as far as CO and NO_x emissions are concerned. Some flame instability problems were though registered, especially for one of the catalytic burner mattresses employed, at low specific power inputs and excesses of air (<375 kW/m² and <12%, respectively). Further, PdO/Pd transition is shown to influence the dynamic behaviour of the catalytic burners.     

丙酮低压一步法合成甲基异丁基酮催化剂体系研究进展

对丙酮低压一步法合成甲基异丁基酮所需要的催化剂体系及反失活机理进行了详尽的综述，并对近年来的研究工作进行了系统地分析与比较，提出了未来的研究方向。     

Bi3+对纳米MnO2水热合成的影响研究

在中性和酸性条件下，以MnO2作为锰源，通过水热合成了纳米MnO2，通过XRD和TEM对产物进行的观察表明，在酸性条件下，向溶液中添加一定量的Bi^3 ，产物的晶型由α型向γ型转化，产物形貌由针状、丝状向颗粒状转变。     

基于知识的服装CAD

本文提出一种基于知识的计算机辅助服装设计系统，该系统运用了人工智能中产生式和框架思想，把服装设计中智能和各种常识和技能进行抽象，把服装按人体部位进行自上而下的分层，从而把一个很复杂的问题转变为简单问题。本文同时提出真实显示服装效果图的数学模型。     

VHDL逻辑综合及FPGA实现

运用ＶＨＤＬ语言描述了一个１２×１２位的高速补码阵列乘法器。重点是运用ＶＨＤＬ逻辑综合优化该乘法器，并进行了乘法器的ＸｉｌｉｎｘＦＰＧＡ实现、功能仿真和时序仿真。经选用ＸＣ４００５ＰＣ－８４－４芯片进行验证，证明了其正确性