EIS evaluation of the filiform corrosion of aluminium coated by a cataphoretic paint

Filiform corrosion is mainly considered as a cosmetic attack and is undesirable in most applications. The initiation and propagation of the filaments are related to different parameters such as the presence of defects, the permeability of the coating to water and oxygen, the adherence of the paint system and the presence of salts.

The aim of this work is to study the behaviour of painted aluminium samples towards filiform corrosion or delamination. The 6082 Aluminium alloy was selected and the samples were covered with a cataphoretic epoxy primer without lead (PPG Industries France). Prior to the application of the electrocoat, the samples were pre-treated by a commercial Zr/Ti or chromate conversion treatment or simply etched with a commercial acid etching product.

Filiform corrosion was studied by the normalized test (ISO/DIS 4623): painted and scratched samples were inoculated in HCl and exposed in a constant humidity chamber at 40 °C and 82% RH for 3 weeks. After exposure the samples were subjected to a visual and optical microscopic examination.

Electrochemical impedance spectroscopy was used to study the sensitivity to filiform corrosion. The operating mode of this test is similar to the normalized one. The samples were scratched before inoculation for 1 h in HCl and then exposed to the humidity chamber for a maximum of 4 days. The samples were tested by EIS in an acidified 0.1 M Na₂SO₄ electrolyte solution. The resulting impedance spectra were analyzed with an appropriate equivalent electrical circuit which allows the evaluation of the exposed metallic surface area, directly related to the extent of filiform corrosion or delamination. Different parameters were varied: the exposure time in the humidity chamber; the immersion time in the electrolyte sulphate solution as well as its pH and the coating thickness.     

西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理

通过西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理施工方法论述,给出了加砂层振冲碎石桩施工造孔水压、水量、成孔速度、填料级配、填料方法以及振密电流值、留振时间等施工控制参数。     

Grain Growth Behavior of 5Cr21Mn9Ni4N Steel Micro-Alloyed by Rare Earth

Grain growth behavior of 5Cr21Mn9Ni4NRE steel was experimentally studied at various solid solution treatment temperatures and holding for different times. The experimental results show that the 5Cr21Mn9Ni4NRE steel has the feature of sharp austenite grain coarsening after solid solution treatment at the temperature above 1150 ℃. RE added in the steel has the benefit to restrain grain growth and increase grain growth activation energy.     

摩擦焊在钢制实心抽油杆修复中的应用

通过对焊接工艺及焊后热处理工艺优化，采用摩擦焊接技术对报废抽油杆中仍有使用寿命的杆头与杆体进行了拼接，获得了性能达标的抽油杆。从而提高了旧杆的修复率．降低了采油成本。该技术可在抽油杆修复及相关行业进行推广应用。     

探讨电石法PVC烟气治理方法

分析了电石法PVC生产链中电石炉烟气及电厂烟气二氧化硫的排放情况,指出利用电石炉烟气中的CO合成氨、再将合成氨用于燃煤电厂烟气的"氨法"脱硫是具有较大应用潜力的循环经济产业链。     

4%Cr铸钢支承辊热处理工艺

以太钢1549轧机采用的4%Cr铸钢支承辊为依托,研究了该辊子从铸造成形到最终精加工之间的三次热处理工艺。最终达到其技术要求:辊身硬度65~70HS、淬硬层深≥70 mm、辊颈硬度42~48HS。     

生物除臭滤池在污水厂污泥处理段的除臭效能

对采用天然有机滤料和合成无机滤料的生物除臭滤池在加拿大多伦多市Ash-bridge’s Bay污水厂污泥处理站的干化和转运段的应用效果进行了分析。详细介绍了污泥脱水工艺、臭气的产生及其组分，进而对软木树皮滤料和矿物合成永久性滤料的除臭效果进行了比较。还讨论了一些具体的运行经验，并采用动态模型对不同条件下的运行数据进行了分析。     

用土壤含水层处理系统去除水库微污染有机物的试验研究

本文针对当前中国饮用水源污染以微污染为主的特点，以北京三家店水库原水和永定河河道砂为研究对象，设计了用于表征土壤含水层处理系统的一维土柱，进行污水净化效果的试验研究。结果表明，土壤含水层处理系统对三家店水库微污染水中的有机物有一定的去除效果，在0．12m／d的水力负荷条件下，对CODMo去除率虽然仅为15％，但是出水达到了地表水Ⅱ类水质标准；对BOD5的去除率达到了55％，可以被有效地去除。渗透速率相同时，水力负荷周期对去除效果的影响不明显，但在保证一定水力负荷的情况下，可适当延长落干期，恢复土壤的渗透能力，达到较好的处理效果。同时，土壤含水层处理系统的净化能力主要发生在土层50cm以内。     

60Si2Mn合金钢发蓝泛红的分析研究

本文探讨了60Si2Mn合金钢发蓝原理，针对其膜层泛红问题，分析了热处理、表面前处理、发蓝及浸油等过程对发蓝质量的影响，由此采取了相应的技术措施，生产实践证明发蓝质量稳定，生产效率明显提高。     

粪便水对大坦沙污水厂生产运行的影响及控制措施

广州市大坦沙污水处理厂承担着全市粪便水的处理任务。生产实践表明，由粪便水造成的水质冲击负荷对生产运行不利，导致设备维护率提高、运行成本增加。通过建造粪便水调节池、调整工艺参数、加大设备维修和技术改造力度、对恶臭源进行加盖除臭等措施可以降低粪便水对生产运行的影响。