中国企业互联网网站拥有状况分析

介绍了中国企业拥有自有网站现状，分析了中国企业网站拥有率明显偏低的多种原因，探究了互联网时代中国企业发展并充分利用自有网站的途径和方法。     

预应力轴心受拉钢构件高温性能试验及理论研究

进行了3根预应力轴心受拉钢构件高温试验研究。试验结果表明，高温下预应力轴心受拉构件中内置拉索和钢管所承受荷载比例随温度的变化而不断变化。升温初期拉索张力随温度升高不断增大，预应力轴心受拉钢构件轴向位移平稳发展，在达到峰值后，拉索张力随升温时间的延长而不断降低。在临界状态下，轴向位移增长很快， 预应力受拉构件中拉索均被拉断，外部钢管发生不同程度的颈缩现象。在试验结果的基础上，建立了预应力轴心受拉钢构件的有限元分析模型，得到了高温作用下预应力轴心拉杆中拉索张力和预应力钢杆轴向位移的时程全曲线。参数分析的结果表明：在其他条件相同时，预应力轴心受拉钢构件失效时的临界温度随着荷载比的增加而降低；当预应力比小于08时，预应力比对预应力轴心受拉钢构件失效时的临界温度的影响较小，当预应力比等于08时，预应力轴心受拉钢构件失效时的临界温度显著的提高；在其他条件相同时，预应力轴心受拉钢构件失效的临界温度随约束刚度比的增大而增大。最后对高温下预应力轴心受拉钢构件进行了理论分析，推导出预应力轴心受拉钢构件高温下差分计算方法，并以此为基础编写程序。通过计算结果与试验结果的对比，证明了差分计算方法的正确性。     

An unsupervised learning method with a clustering approach for tumor identification and tissue segmentation in magnetic resonance brain images

Malignant and benign types of tumor infiltrated in human brain are diagnosed with the help of an MRI scanner. With the slice images obtained using an MRI scanner, certain image processing techniques are utilized to have a clear anatomy of brain tissues. One such image processing technique is hybrid self-organizing map (SOM) with fuzzy K means (FKM) algorithm, which offers successful identification of tumor and good segmentation of tissue regions present inside the tissues of brain. The proposed algorithm is efficient in terms of Jaccard Index, Dice Overlap Index (DOI), sensitivity, specificity, peak signal to noise ratio (PSNR), mean square error (MSE), computational time and memory requirement. The algorithm proposed through this paper has better data handling capacities and it also performs efficient processing upon the input magnetic resonance (MR) brain images. Automatic detection of tumor region in MR (magnetic resonance) brain images has a high impact in helping the radio surgeons assess the size of the tumor present inside the tissues of brain and it also supports in identifying the exact topographical location of tumor region. The proposed hybrid SOM-FKM algorithm assists the radio surgeon by providing an automated tissue segmentation and tumor identification, thus enhancing radio therapeutic procedures. The efficiency of the proposed technique is verified using the clinical images obtained from four patients, along with the images taken from Harvard Brain Repository.     

Density and Young׳s Modulus of ternary glasses close to the eutectic composition in the CaO–Al2O3–SiO2-system

The elastic properties and the density of ternary glass forming systems within the CaO–SiO₂–Al₂O₃-system (CAS) were evaluated. Different glass compositions near the lowest eutectic (1170 °C) composition within the CaO–Al₂O₃–SiO₂-system have been melted from pure raw materials. Their target compositions differed not more than 4 wt% for each component. Exact chemical compositions were measured by x-ray fluorescence. The density, and acoustic properties were determined and the Young׳s Moduli were derived herefrom. It was of special interest to obtain information on these properties and their dependencies upon small variations in the composition. The density values were between 2.600 and 2.667 g cm⁻³ and the packing density factors V_p of the oxides glasses using the ionic radii of Pauling were in the range from 0.559 to 0.571. The determined data were compared to different model calculations. Density model calculations show relative deviations between 2 and 6%. The values calculated from the model for Young׳s Modulus by Makishima and Mackenzie (1973) [1] were somewhat smaller than the measured ones. The correction by Rocherulle et al. (1989) [3] of the Makishima model showed better agreement with the measured values.     

The influences of textural parameters of grains on the LCPC abrasivity of coarse-grained igneous rocks

Rock abrasivity causes the tool wear in rock excavation or drilling. The understanding of wear mechanism is important for the cost estimation and planning of projects. In this study, the effects of textural properties of grains such as aspect ratio, roundness, and diameter on the LCPC abrasivity coefficient (LAC) were investigated for coarse-grained igneous rocks. First, the LAC was correlated to the abrasive mineral content (AMC) and a good correlation was found between the two parameters. Then, the LAC was correlated to the AMC multiplied by the textural properties of grains, respectively. Compared to the correlation coefficient of the relation between the LAC and the AMC, the correlation coefficient was increased by including the textural properties of grains to the correlation. A combined parameter called shape and size coefficient (SSC) was defined in order to see the combined effect of the textural properties of grains on the LAC. The correlation coefficient of the relation between the LAC and the AMC multiplied by the SSC is very strong and fairly higher than that of the previous correlations derived. It can be concluded that the textural properties of loosened materials have a strong influence on the tool wear.     

Selective recovery of valuable metals from partial silicated sphalerite at elevated temperature with sulfuric acid solution

The purpose of this work was to study the feasibility at laboratory-scale of a hydrometallurgical process for the selective recovery of valuable metals from partial silicated sphalerite in an oxygen pressure acid leaching system. The factors influencing dissolution efficiency of the ore were investigated and optimized. Under optimum conditions (i.e., temperature of 433 K, sulfuric acid concentration of 41.2 g/L, leaching time of 2.5 h, liquid/solid ratio of 6 mL/g, and pressure of 1.6 MPa) over 97% Zn was extracted into the leach liquor together with 0.3% SiO₂ and 2.9% Pb. The leaching slurry had good solid–liquid separation characteristics, and the filtration rate could be as high as 716 L/m² h. About 96% oxidation of sulfide sulfur to sulfate was achieved under these conditions. Analysis of the content of elemental sulfur in the leaching residues indicated that the fraction of sulfide sulfur determined as elemental sulfur was about 10% at 393 K, and that it decreased with temperature down to 0.5% at 453 K. Ultimate solid residues, which have been concentrated in silica and lead, can be oriented toward the lead smelter after alkali roasting-water washing pretreatment for metal recovery.     

一种提升汽车覆盖件材料利用率的方法

在多款车型实践基础上,总结了一种提升汽车覆盖件材料利用率的方法,给出了工作流程图,即在同步设计开发或油泥车阶段,应用板料成形CAE模拟手段,通过优化零件边界、工艺补充面、坯料形状的交互试错,获得了优化的零件状态和合理的工艺方案,实现了材料利用率的最优化;以B车型的轮罩外板零件为实例,采用上述方法可将该零件的材料利用率从38.04%提升到56.67%,每台节省材料3.61 kg、实现效益22.96元,证实了该方法有效可行。     

Dispersed air flotation and foam fractionation for the recovery of microalgae in the production of biodiesel

Microalgae biomass has great potential for being used as feedstock for the sustainable production of biodiesel, as it is able to produce 7–31 times more oil than the top terrestrial crop. It is a green alternative to the currently utilized energy sources as it can reduce CO, CO₂ and hydrocarbon emissions. However, downstream processing costs for the dilute biomass are a major challenge. Foam flotation has been recently investigated for the recovery of microalgae cells from dilute liquid suspensions. A number of variables on the effectiveness of foam flotation for microalgae have been investigated, which include surfactant type and concentration, cell concentration, pH, hydrophobicity, time, growth stage, flow rate, ionic strength, alkalinity, temperature, bubble size, and column size. It appears to be a promising method for the recovery of algae for biofuel production, as a result of the high removal recoveries, good enrichment ratios, ability to process large volumes of biomass, and its ease of operation. However, literature on this subject is scarce, and there are research gaps that should be investigated including characterization of microalgae cells and impact on foam separation and the effect of surfactant as a treatment prior to lipid extraction.     

Improve the signal to noise ratio and installation convenience of the inductive coil for wire rope nondestructive testing

Inductive coil is used as the nondestructive testing sensor of a wire rope or a pipe, because of its low cost and high durability. However, the winding structure is complex and difficult to design during the field test. Hundreds or even thousands of turns are needed to improve the signal to noise ratio (SNR) and the data processing is cumbersome. In this paper, based on the theoretical analysis and 3D transient magnetic field simulation, a kind of iron core is presented as coil winding skeleton for the wire rope nondestructive testing. Additional iron core plays a role of magnetism concentration, where the magnetic flux leakage (MFL) path is changed and the MFL of the defect is converged to the core. Therefore, the SNR of the coil which is wound on the iron core is improved, and the coil winding skeleton is simplified with the iron core structure optimization. Meanwhile, the influence of the coil cross-section area on the test result analysis is eliminated, and the influence of the lift-off distance between coil and wire rope on the detection result is also reduced. Finally, it is proved by experiment that the SNR of coil with the iron core proposed in this paper is increased almost six times, which makes it easier for defect analysis.