转底炉处理赤泥工艺技术

为了综合利用氧化铝冶炼产生的赤泥，探索在转底炉中直接还原赤泥、磨矿磁选获得高品位直接还原铁。通过实验室试验摸索了转底炉还原工艺参数，并在转底炉工业试验线进行了工业试验。实验室结果表明，赤泥还原后的直接还原铁(DRI)金属化率可达88.6%，磁选后的铁品位可达82.1%，磁选后的铁回收率可达88.9%。工业试验中，转底炉还原后，产品金属化率平均为69.2%，将还原后的DRI磁选获得高品位的DRI产品，磁选后DRI的铁品位为72.8%，磁选后铁回收率达到了85.2%,初步打通了在转底炉中还原赤泥、磁选的工艺路径。     

重力注水过程流动不稳定现象关键影响因素研究

重力驱动注水过程中由于流量较小以及蒸汽的积聚可能导致流动不稳定现象的发生，对核反应堆安全运行具有重要的影响。通过实验研究的方法，搭建了重力注水模拟实验装置，研究了不同蒸汽出口形阻、高位储水箱水位和加热棒初始温度下流动不稳定现象的变化规律。结果表明，重力驱动注水过程流动不稳定现象包含冷却水初次注入阶段、注入水逐出阶段和冷却水再注入阶段等。在一定冷却水初始温度、冷却水入口形阻以及系统压力下，蒸汽排出速度以及实验本体内筒顶部的聚集情况取决于蒸汽出口形阻，减小蒸汽出口形阻可加快蒸汽排放速度，压力峰峰值降低、振荡周期变长，有利于系统稳定；提高高位储水箱水位加快了冷却水注入速率，增加了加热棒被淹没率，降低了流动不稳定现象的发生次数和持续时间；随加热棒初始温度的升高，冷却水流量出现了波动向停滞的转变，流动不稳定现象发生的次数增加且持续时间加长。     

Flow state monitoring of gas-water two-phase flow using multi-Gaussian mixture model based on canonical variate analysis

As a highly complex and time-varying process, gas-water two-phase flow is commonly encountered in industries. It has a variety of typical flow states and transition flow states. Accurate identification and monitoring of flow states is not only beneficial to further study of two-phase flow but also helpful for stable operation and economic efficiency of process industry. Combining canonical variate analysis (CVA) and Gaussian mixture model (GMM), a strategy called multi-CVA-GMM is proposed for flow state monitoring in gas-water two-phase flow. CVA is used to extract flow state features from the perspective of correlation between historical data and future data, which solves the cross correlation and temporal correlation of multi-sensor measurement data. GMM calculates the possibility that the current flow state belongs to each typical flow pattern and judges the current flow state by probability indicators. It is conducive to follow-up use of Bayesian inference probability and Mahalanobis distance-based (BID) indicator for flow state monitoring, which avoids repeated traversal of multiple CVA-GMM models and improves the efficiency of the monitoring process. The probability indicators can also be used to analyze transition flow states. The method combining the probabilistic idea of GMM with the deterministic idea of multimodal modeling can accurately identify the current flow state and effectively monitor the evolution of flow state. The multi-CVA-GMM method is validated by using the measured data of the horizontal flow loop of gas-water two-phase flow experimental facility, and its effectiveness is proved.     

Comments on “Study and application of discharge calibration for submerged radial gates” by Guo X., Guo Y., Wang T., Fu H., Li J. Flow Meas. Instrum. 78 (2021) 101912, https://doi.org/10.1016/j.flowmeasinst.2021.101912

This paper discusses the capability of Guo et al.'s (2021) equations to determine the discharge of radial gates under submerged flow conditions. It was concluded that Guo et al.'s (2021) equations are associated with error reduction compared to the Incomplete Self-Similarity (ISS) theory and the calibration method. However, it does not have a significant advantage over Energy-Momentum (E-M) approach. Employing E-M principles, new equations were proposed to determine the discharge of radial gates, which has some advantages compared to Guo et al. (2021), such as (1) error reduction under partially and fully submerged flow conditions, (2) least dependence on the empirical constants, (3) uniformity of form over the entire submerged condition, and (4) no need to classify the submerged flow. Field calibration showed that the proposed equations in the present study for a single gate predict the discharge of parallel radial gates with a mean absolute error of less than 4.5% subject to the submerged operation of all open gates.     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

共价有机框架材料及其在关键核素分离中的应用进展

共价有机框架材料（COFs）是一类由共价键连接的多孔晶态材料。因具有单体链接方式灵活、结构可调、活性位点丰富、比表面积大、理化性质相对稳定等特点，它们在气体储存与分离、能量储存、催化和光电学领域受到了广泛的关注。本文主要从结构设计、合成方法及功能化、材料的分析表征和晶形控制等方面概括地介绍了COFs材料。在此基础上，综述了COFs材料在关键核素分离方面的研究进展，并展望了其在核素分离领域的应用前景和今后的研究方向。     

Fabrication of BSCF-based mixed ionic-electronic conducting membrane by electrophoretic deposition for oxygen separation application

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF), which exhibits a high mixed oxide ionic-electronic conduction, was used for the fabrication of an oxygen separation membrane. An asymmetric structure, which was a thin and dense BSCF membrane layer supported on a porous BSCF substrate, was fabricated by the electrophoretic deposition method (EPD). Porous BSCF supports were prepared by the uniaxial pressing method using a powder mixture with BSCF and starch as the pore-forming agent (0–50 wt.%). The sintering behaviors of the porous support and the thin layer were separately characterized by dilatometry to determine the co-fired temperature at which cracking did not occur. A crack-free and thin dense membrane layer, which had about a 15 μm thickness and >95% relative density, was obtained after optimizing the processes of EPD and sintering. The dense/porous interface was well-bonded and the oxygen permeation flux was 2.5 ml (STP) min⁻¹ cm^-2 at 850 °C.     

Computational modelling of water flow inside laboratory Knelson concentrator bowl

Enhanced gravity concentrators such as Knelson concentrator (KC) are extensively used in the mineral processing industry. The complexities of KC bowl geometry and variation of feed characteristics have forced process engineers to design empirically new units using laboratory and pilot-scale Knelson concentrators. However, numerical modelling methods such as computational fluid dynamics (CFD) and discrete element method (DEM) provide a better insight of flow behaviour of fluid and particulate solid phases inside these processing units. This article reports findings of CFD simulations for single-phase water flow inside the laboratory KC. An available standard 7.5-cm laboratory KC bowl was numerically simulated using realisable k-ε turbulence model to resolve the turbulence dispersion of existing transitional flow regime. The effects of relative centrifugal force (RCF) intensity and bed fluidisation water flow rate on the water velocity and pressure distributions were studied. Simulations confirmed the swirling flow pattern governing inside the bowl. The results revealed that the impact of RCF intensity on the water field values is greater than that of bed fluidisation water flow rate. Both velocity and pressure variations inside the bowl rings followed a linear trend.     

溶胀嵌入脂肪酸分子制备高脱硼反渗透膜

采用“溶胀-嵌入-收缩”方法改性聚酰胺反渗透膜，制备了一种高脱硼反渗透膜。通过甲醇溶胀增加了高分子链之间的距离，为疏水性癸酸分子的嵌入提供了场所，然后在压力和浓差极化共同作用下，改性分子选择性嵌入聚酰胺膜的孔内；当甲醇分子离开后，聚酰胺膜收缩将癸酸分子固定在高分子网络中。实验借助溶胀和分子嵌入以及溶胀后的收缩调节聚酰胺膜的孔径大小；利用脂肪酸的疏水性降低聚酰胺膜的极性，从而实现增加空间位阻和减少氢键结合位点数量的目的。实验结果显示，改性膜的脱硼率和截盐率均明显升高，截盐率从90.36%增加到96.46%，脱硼率从未改性膜的47.85%增加到77.32%，渗透液的硼含量达到WTO的使用标准。虽然水和硼的渗透性均下降，但是水和硼的渗透选择性增加，证明该方法有利于提高水硼选择性。     

A modified cross-correlation algorithm for PIV image processing of particle-fluid two-phase flow

PIV (Particle Image Velocimetry) technique for flow field measurement has achieved popular self-identify through over ten years development, and its application range is becoming wider and wider. PIV post-processing techniques have a great influence on the success of particle-fluid two-phase flow field measurement and thus become a hot and difficult topic. In the present study, a Phase Respective Identification Algorithm (PRIA) is introduced to separate low-density solid particles or bubbles and high-density tracer particles from the PIV image of particle-fluid two-phase flow. PTV (Particle Tracking Velocimetry) technique is employed to calculate the velocity fields of low-density solid particles or bubbles. For the velocity fields of high-density solid particles or bubble phase and continuous phase traced by high-density smaller particles, based on the thought of wavelet transform and multi-resolution analysis and the theory of cross-correlation of image, a delaminated processing algorithm (MCCWM) is presented to conquer the limitation of conventional Fourier transform. The algorithm is firstly testified on synthetic two-phase flows, such as uniform steady flow, shearing flow and rotating flow, and the computational results from the simulated particle images are in reasonable agreement with the given simulated data. The algorithm is then applied to images of actual bubble-liquid two-phase flow and jet flow, and the results also confirmed that the algorithm proposed in the present study has good performance and reliability for post-processing PIV images of particle-fluid two-phase flow.