空调器用风冷冷凝器换热能力实验研究

实验测定了几种不同铜管、肋片组合的冷凝器在不同的风量和风机转速下的换热量，发现采用内螺纹铜管和迎风侧平片、背风侧冲缝片的冷凝器具有最优的换热性能。分析了多流路冷凝器中不同流路之间的制冷剂分配不均匀性和再热现象。     

铜在高纯净钢中析出过程的观察

利用透射电子显微镜观察了铜在高纯净钢中的析出过程，发现早期析出阶段有类B2结构的亚稳相出现，分析了铜在高纯净钢中的析出贯序，研究结果对分析铜在高纯净钢中的时效强化机理具有重要意义。     

Copper phthalocyanine as corrosion inhibitor for ASTM A606-4 steel in 16% hydrochloric acid

A study based on the corrosion inhibition properties of copper phthalocyanine is described. Coverage degrees of copper phthalocyanine (Cu-phcy) on ASTM-A606-4 steel, obtained by weight loss measurements, were fitted to Langmuir, Frumkin, Temkin and Flory–Huggins adsorption isotherms. A better fit to the Langmuir isotherm was obtained. The polarization curves showed that polarization of both the anodic and cathodic reactions were verified for concentrations higher than 10^–4 M, indicating a mixed type action. Only the anodic reactions were polarized for lower concentrations. At high frequencies the Nyquist diagrams showed one capacitive loop attributable to double layer charging and a small one at intermediary frequencies attributable to the faradaic process of hydrogen evolution. The formation of an adsorbed film was characterized by increasing charge transfer resistance values in the low frequency range for increasing inhibitor concentrations. According to the techniques used in this study, copper phthalocyanines showed a high corrosion inhibiting efficiency for all concentrations.     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。     

对乙酰基偶氮胂与铜的显色反应研究及应用

研究了对乙酸基偶氮肿与铜的显色反应。结果表明，在弱酸性介质中，铜与对乙酰基偶氮胂形成稳定的蓝色配合物，其最大吸收峰位于６２０ｎｍ，表观摩尔吸光系数达４．８６×１０４Ｌ·ｍｏｌ－１·ｃｍ－１。配合物的组成比为Ｃｕ：对乙酰基偶氮胂＝１：２，表现稳定常数为１．８９×１０１０，铜的含量在０～４０μｇ／２５ｍＬ范围内符合比尔定律。显色反应具有较好的选择性，应用于铝合金中铜的测定，结果满意。     

Gildes model studies of aqueous chemistry. III. Initial SO2-induced atmospheric corrosion of copper

The GILDES computer model, incorporating Stumm's concept of proton- and ligand-promoted dissolution, has been used to simulate the exposure of copper at room temperature to 210 ppb sulfur dioxide and 80% relative humidity. The agreement is good between the calculations and laboratory exposures performed under these exposure conditions. Surface reactions are relatively more important at lower relative humidities and the dominant corrosion products formed are solid state Cu₂SO₃, CuSO₃ and Cu₂U. Free-radical redox processes are important participants and control the relative distribution of Cu(I)- and Cu(H)-containing corrosion products.     

铜蒸汽激光器双闸流管触发系统的研究

研制成用于钢蒸汽激光器的双间流管触发系统。用两个闸流管并联进行交替触发，总输入电功率达7．8kW。低功率运行时，激光器的效率为0．6％与单间流管激光器的效率一致。     

废电解液除杂制取硫酸铜和粗镍

介绍了废电解液除杂制取硫酸铜和粗镍的主要工艺条件及试验结果。在废电解液中加入CH80调节pH值到一定范围后,再加入CH64将电解液中Fe2+等杂质除去,铁的去除率可达到94%～98%。然后向滤液中加入CH80调节pH值沉淀铜。过滤后的滤饼用H2SO4溶解后再结晶,可得到CuSO4·5H2O晶体。滤液中加入Na2CO3沉淀镍,过滤后的滤饼即为粗镍(NiCO3)。铜和镍的回收率分别达96%和90%。该流程简单,投资少,效益高,环境保护好,在工业上有较广的应用前景。     

Mechanism for the Peritectic Reaction and Growth of Aligned Grains in YBa2Cu3O6+x

It is experimentally observed that the peritectic reaction, 211 + liquid → 123, can be driven essentially to completion in 1 h at an undercooling of only ∽30°C. The kinetic data, together with the observed microstructures, are inconsistent with the normal mechanism of the peritectic reaction. It is proposed that the mechanism of the reaction involves dissolution of 211 particles into the liquid and precipitation of solid 123. The aligned grain structure is explained through sympathetic nucleation of new 123 grains on existing grains.     

超高纯铜的制备方法和应用

简要介绍了超高纯铜(UHPC)的几种精炼方法，以及它在工业方面的应用。并对超高纯铜的研究开发趋势及应用前景进行了展望。