拉伸试样弯曲度对屈服强度测试值的影响

分析了输送管管体横向拉伸试样弯曲度对屈服强度测试值的影响,从理论上初步阐明了管体横向拉伸试样的弯曲会引起屈服强度测试值的降低,并提出在相关的标准中应对管体横向试样的展平程度作出规定.     

预测井眼稳定性的力学化学耦合方法

在井眼力学稳定性评价的基础上，将硬脆性页岩水化后岩石强度等参数的变化规律用于页岩水化前后坍塌压力变化的对比分析，结果表明，地层坍塌压力当量密度随页岩水化程度的增加逐渐升高。给出了预测井眼稳定性的力学化学耦合方法，并将该方法应用于现场生产中，取得了较好的预测效果     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

几种高强度钢腐蚀疲劳裂纹扩展行为的研究

本文研究了ＧＣ－４，３０ＣｒＭｎＳｉＮｉ２Ａ和３００Ｍ超高强钢的腐蚀疲劳裂纹扩展行为。考虑了环境，热处理制度，应力比和频率对裂纹扩展的影响。研究结果表明：腐蚀环境和热处理制度对疲劳裂纹扩展有显著影响。在侵蚀性环境中随频率降低，裂纹扩展大幅度上升，随应力比提高，环境影响加剧。利用扫描电镜对试样断口形貌进行了分析，并讨论了高强钢的腐蚀疲劳机理。     

用微脱胶技术表征芳纶纤维材料界面强度

采用微脱胶原位技术表征了Ａｐｍｏｃ，芳纶－Ⅱ纤维复合材料界面结合强度。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

The mechanics of compressive kinking in unidirectional fiber reinforced ductile matrix composites

Three distinct stages of kink band formation and propagation exist in ductile matrix composites subjected to compressive loading. These stages are called incipient kinking, transient kinking and kink band broadening. Each stage involves a different deformation mode. The mechanics governing each stage are discussed. Incipient kinking, where the peak load is attained, and kink band broadening, where the load attains a steady-state, are important in structural design. Two design philosophies are presented. References to pertinent literature are made throughout.     

RS高强Al－Zn－Mg－Cu系合金热处理温度与性能的关系

本文系统研究了ＲＳ高强Ａｌ－Ｚｎ－Ｍｇ－Ｃｕ系合金淬火温度、时效温度与性能关系，同时还分析了合金的微观组织。试验得出在４７０℃淬火峰时效（Ｔ６）的拉伸性能达到σ_ｂ＝７４０ＭＰａ，σ_（０．２）＝７０２ＭＰａ，δ_５＝１０％；双级时（Ｔ７３）可获得σ_ｂ＝６３３ＭＰａ，σ_（０．２）＝６０６ＭＰａ，δ_５＝１１．５％。合金的弥散强化相是Ｃｏ_２Ｎ_９、Ａｌ_３Ｚｒ，沉淀强化相为ＧＰ区、η＇和η。     

反向凝固法生产H90-钢-H90复合带

研究H90-钢-H90反向凝固复合过程中复合层厚度的变化规律以及复合带的组织和性能，探讨界面结合机理。结果表明：随着浸渍时间的增加，复合层的厚度变化经历了凝固生长、平衡相持和回熔3个阶段，钢带的预热温度越低，获得的最大复合层厚度越厚；H90复合层的组织为等轴晶粒，复合界面处Cu和Fe发生了扩散，而Zn未发生明显扩散，扩散层较薄，约为4μm；复合带的界面结合牢固；不同复合层厚度的复合带，其力学性能略有差异，但均达到GB5213——85所规定的F级深冲钢板的力学性能要求。     

不锈钢精密薄壁件外表面磁力研磨工艺研究

磁性研磨是一种利用磁场中的磁性磨料,对具有相对运动的工件表面进行光整加工的新技术。选择铝、镍、钴磁粉作为磁性磨料时,对奥氏体不锈钢精密薄壁件外表面具有良好的研磨作用。