复合高稳定性固态二氧化氯释放剂的研究

目前中国市场上固态二氧化氯释放剂技术不成熟，产品多为二元包装或伪一元包装，给使用和储存带来很多不便。为解决这个问题，采取亚氯酸钠为释放剂主成分，辅以复合无机盐活化剂，借助小丸包衣技术，制备了一元化、高纯、高稳定性固态二氧化氯释放剂。     

C80高强粉煤灰混凝土及其应用

本文研究了粉煤灰替代部分水泥配制Ｃ８０砼的压蒸工艺技术，结果表明，采用此技术可以稳定生产Ｃ８０混凝土和高强预应力混凝土管桩（简称ＰＨＣ桩）。     

一种耐超高温、耐酸聚合物的制备及性能测试

摘要：为解决常规聚合物无法满足超高温深井酸化压裂的技术要求，本文分别以丙烯酰胺（AM） 甲基丙烯酰氧乙基三甲基氯化铵（DMC）、AM DMC SMA（十八烷基甲基丙烯酸酯）为原料，通过自由基聚合制备出两种耐酸聚合物SY-1和SY-2，并对其结构进行表征及性能测试。结果表明：SY-2红外谱图中720 cm-1为—(CH2)n—的弯曲振动吸收峰，单体成功接枝到聚丙烯酰胺分子链上；热重分析表明，SY-1升温至600℃失重比为98%，SY-2失重比86%，热稳定性得到改善；质量分数为20%盐酸中，SY-2质量分数0.8%：180℃，170s-1流变性能测试，SY-2剪切终点黏度56mPa?s，90℃、120℃、150℃剪切1h，黏度为83.6mPa?s、43.5mPa?s、27.8mPa?s，剪切稳定性分别为85.66%、74.45%、52.01%； 180℃、3MPa条件下，静态酸岩反应速率为8.94?10-5(g/cm2?s)，较常规SY-1反应速率1.69?10-4(g/cm2?s)减小一个量级。且与缓蚀剂、铁离子稳定剂配伍性良好，克服高温酸化压裂技术的应用瓶颈。     

超高分子相对质量部分水解聚丙烯酰胺合成研究

选择AM均聚后水解工艺路线,采用新型复配引发体系,合成作为油田驱油剂的超高相对分子质量聚丙烯酰胺(简称PAM).在所选高效的引发体系下,考察了主要聚合反应因素对产品平均分子相对质量的影响,确定了聚合工艺条件溶液的pH值为11～11.5,W(单体)为45%,W(引发剂)为70×10-6,W(链转移剂)为1.3×10-6.在优化的聚合条件下,合成了相对分子质量高达25×106,水解度在20%～30%可调,过滤比小于1.3的聚丙烯酰胺.     

高气速下鼓泡塔中气含率分布的测定

在内径476 mm的鼓泡塔内用压差法测定全塔平均气含率与表观气速的关系,进一步利用响应特性良好的双电导探针,考察了不同气速下局部气含率的分布规律。实验结果表明,利用探针法计算得到的全塔平均气含率值与压差法测定值平均误差仅为4.5%,表明探针法测量局部气含率的可靠性良好。实验还表明在高气速下,除分布板影响区外,局部气含率均类似抛物线型分布;随着气速增加,气含率分布趋于陡峭。以实验为依据,拟合了不同气速下(0.05~1.0 m/s)鼓泡塔中局部气含率的关联式,认为塔内局部气含率与径向位置、表观气速和塔径等因素有关。     

Complete Elastic Tensor for Mullite (∼2.5Al2O3·SiO2) to High Temperatures Measured from Textured Fibers

Directionally solidified mullite fibers have been grown by the laser-heated, float-zone method from starting materials with a nominal composition of 3Al₂O₃·2SiO₂. The fibers used in this study have large single-crystal regions with composition 2.5Al₂O₃·SiO₂ and (001) fiber axis orientation. The complete elastic tensor of these samples has been determined by Brillouin spectroscopy at room temperature and elevated temperatures up to 1200°C. Isotropic moduli (bulk, shear, and Young's) have been calculated using the Voigt–Reuss–Hill averaging scheme. The room-temperature values obtained are K _VRH= 173.5 ± 6.9 GPa, G _VRH= 88.0 ± 3.5 GPa, E _VRH= 225.9 ± 9.0 GPa. All moduli show gradual, linear decreases with temperature. The temperature derivatives obtained for the equivalent, isotropic moduli are d K _VRH/d T =−17.5 ± 2.5 MPa/°C, d G _VRH/d T =−8.8 ± 1.4 MPa/°C, d E _VRH/d T =−22.6 ± 2.8 MPa/°C. Substantial differences between bulk properties calculated from the single–crystal measurements in this study and the properties reported in the literature for polycrystalline sintered mullite are identified, indicating the importance of factors such as microstructure, intergranular phases, and composition to the elasticity of mullite ceramics.     

高沸点溶剂法合成原乙酸三甲酯

对低沸点溶剂法制备原乙酸三甲酯工艺进行了改进，比较了煤油、2-乙基己醇、氯苯、异佛尔酮、邻苯二甲酸二丁酯、乙二醇二丁醚等高沸点溶剂对反应的影响，筛选出最优高沸点溶剂煤油：研究了新反应体系的醇解pH值、溶剂的循环使用次数对反应的影响及溶剂循环损耗率，结果表明，醇解的最佳pH值为5．6；随着溶剂循环次数增加，原乙酸三甲酯收率从83．6％(1次)逐渐下降到76．7％(16次)；溶剂次平均损耗率4．6％。实现了直接蒸馏产品，溶剂循环使用的新工艺。避免了旧工艺先蒸溶剂，后蒸产品，产品大量分解，收率低等缺点。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

High Density Culture of Porphyridium cruentum in a 42 L Internal Airlift Loop Photobioreactor

1 INTRODUCTION Porphyridium cruentum is a kind of unicellular microalgae, which can live widely in freshwater, marine, brackish, and soil environment[1]. Great attention has been paid to its potential economic value such as the high content of essential high unsaturated fatty acids, especially arachidonic acid (AA) and eicosapentaenoic acid (EPA) (ca 50% in the total fatty acids), ploysaccharides, and synthetic pigments, especially phycoerythrin (PE)[2,3]. During cultivation, the cells…     

天津爱普生有限公司油墨废水处理方案及运行情况

天津爱普生有限公司废水治理工程设计水量5t／d，废水浓度高，水质、水量变化大。采用水解酸化-生物接触氧化处理工艺对天津爱普生有限公司废水进行处理，进水CODCr，平均为2500mg／L左右，CODCr去除率≥90％，排水各项指标均符合国家污水综合排放标准GB8978-1996的二级排放要求。