浅谈采用短木桩加土工网碎石垫层处理挡墙软基

结合工程实例，对采用传统的短木桩加新兴的土工合成材料——土工网及碎石垫层构成复合基础，处理河岸挡墙软基进行探讨，该方法在软土层厚度不超过4．0m的条件下，技术可靠，施工简单，工期短，造价低。     

基于TiNi合金的超弹性对其相关磨损机制的FEM研究

本文在重点考虑TiNi合金高弹性变形量的前提下，采用等向强化模型，对不锈钢和超弹TiNi合金在法向接触载荷作用下的六种模型进行了有限元(FEM)分析。结果表明：在相同载荷条件下，超弹TiNi合金产生的von Mises弹性应变要高于不锈钢，但其von Mises应力和塑性应变却恰恰相反，在同一载荷下该合金发生塑性变形的区域要小于不锈钢；此外，超弹TiNi合金发生塑性变形要比不锈钢困难，所需的临界载荷值随其最大弹性变形量(屈服点处的应变值)的增加而增加。最后，基于本文的有限元计算结果对超弹TiNi合金的蘑粒磨损和疲劳磨损机制进行了讨论。     

Simulation Modeling of Runoff,Groundwater Flow and Sediment Transport into Kastoria Lake,Greece

Kastoria Lake is located in northwestern Greece. The whole basin of the lake is about 253 km². For the computation of the surface water volume inflowing into the lake from the main streams of the sub-basins located around Kastoria Lake, a rainfall-runoff sub-model is used. A quasi-three-dimensional simulation model of the Kastoria basin aquifer is also realized, in order to estimate the groundwater contribution to the volumetric budget of the lake and the whole basin as well. For the computation of sediment load inflowing into the lake from the main streams of the sub-basins, the rainfall-runoff sub-model is combinedwith a soil erosion sub-model and a sediment transport sub-model for streams. A GIS was developed in the hydrologic basin with all data needed for parameter identification and model application. The data base was enriched by a series of on site measurements of water discharge made in all main streams for one whole hydrologic year. By means of the resulting mathematical sediment model, those sub-basins, which deliver most sediment load to the lake, are identified. On the basis of this identification, a series of control measures, for the reduction of sediment inflowing into the lake, at certain places of the above mentioned sub-basins is proposed.     

Sorption of Acid Green 25 on chitosan: Influence of experimental parameters on uptake kinetics and sorption isotherms

Acid Green 25, which is a diazoic dye bearing two sulfonic groups, is efficiently sorbed on chitosan. The protonation of chitosan may explain the electrostatic attraction of this anionic dye and that its optimum pH is close to 3. Preliminary protonation of amine groups (obtained by contact with a sulfuric acid solution) reduced the variation of solution pH following sorbent addition but significantly reduced sorption performance: the maximum sorption capacity of raw chitosan, 525 mg dye/g (0.84 mmol dye/g), was halved by acidic preconditioning. The acidic conditioning also reduced the kinetic rate—the time necessary to reach equilibrium increased up to threefold depending on the experimental conditions. The size of sorbent particles influenced sorption kinetics and equilibrium because of resistance to intraparticle diffusion, but the sorption appeared to occur not only at the surface of the sorbent but also in the intraparticle network of the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1073–1080, 2003     

纯镁对碳化硼颗粒的常压浸渗

本文研究了纯镁对不同致密度的碳化硼(B₄C)颗粒基片的常压浸渗性;讨论了镁液对B₄C颗粒聚集体常压浸渗的影响因素;提出了浸渗模型。研究表明,纯镁在氩气保护下,800～850℃温度范围保温30min即可浸渗B₄C颗粒聚集体。浸渗深度和宽度随加热温度升高和保温时间延长而增加;常压浸渗的B₄C_P/Mg复合材料具有很高的硬度,B₄C颗粒在基体中分布较均匀。     

钼精矿结球机理及对策研究

钼精矿产品质量的提高、粒度变细,干燥过程中结球现象严重。在氧化钼的焙烧过程中MoS2残留量较高。本文针对这一现象,分析了其结球机理,提出了相应对策及解决办法。     

浅谈黄土高原重点水土流失区的林业生态工程建设

黄土高原重点水土流失区林业生态工程建设的现状可以用“三低”（造林成活率低、保存率低、林木生长率低）来概括，人工林具有矮化，纤细，低产，烯疏4个特征，自然条件，适地适树、苗木质量、造林技术、抚育管护等5个方面的问题是造成“三低”的主要原因，适地适树适法是现阶段防治中造林“三低”的主要技术途径，其核心是“林水平衡”合理布局，适地适树，重视经济树种、抗旱造林以及加强病、虫、鼠、免、牛、羊、危害防治，是搞好区内林业生态建设的主要技术措施。     

Bi3+对纳米MnO2水热合成的影响研究

在中性和酸性条件下，以MnO2作为锰源，通过水热合成了纳米MnO2，通过XRD和TEM对产物进行的观察表明，在酸性条件下，向溶液中添加一定量的Bi^3 ，产物的晶型由α型向γ型转化，产物形貌由针状、丝状向颗粒状转变。     

基于米氏散射及夫朗和费衍射的FAM激光测粒仪

提出了综合运用夫朗和费衍射和米氏散射，即在大粒径范围内采用夫朗和费衍射理论，而在小粒径范围内采用米氏散射理论，来改善小粒径范围内的测量精度，保证激光测粒仪在整个粒径范围内的测量精度。