托盘式湿法烟气脱硫塔阻力特性研究

采用冷态物理模型结合商用CFD(Computational Fluid Dynamics)软件,对山东某火电厂300 MW机组配套托盘塔的流场和阻力特性进行了研究,取得了孔板阻力损失与液气比之间的二次函数关系。研究结果表明,塔内两相流场分布合理,入口处液滴受烟气的拖拽作用形成明显的干湿界面,负荷和液气比是影响脱硫塔阻力的重要因素。当液气比一定时,托盘上方能够维持相对稳定的持液层及鼓泡过程;满负荷运行时,脱硫塔阻力损失约为1600 Pa,其中孔板占1/4,持液层占3/4。拟合获得了托盘区阻力损失同液气比之间的关系,为托盘塔的应用、运行及优化提供了理论指导。     

电场对竖直矩形微槽群润湿及表面温度的影响

微槽群在热流密度较大时会达到其毛细极限，可通过主动换热方式之一——电水动力学效应对其进行强化。本文为了研究电场对微槽群表面润湿特性和温度分布的影响，采用平板电极提供电场，蒸馏水作为工质，使用高速相机拍摄微槽内液体润湿长度，测量误差为2.97%～7.46%；使用红外热像仪拍摄电场作用下微槽群表面温度分布，测量误差为2.1%～2.39%。热流密度测量误差范围是9.66%～11.11%。结果表明：电场通过驱动微槽内流体向加热区域流动而提升其润湿性能，且较低热流密度下提升更好。因润湿性能的提升，微槽表面温度得以下降。随着电场增强，微槽横向温度分布的“波峰”、“波谷”差别加大，微槽纵向温度明显降低。当热流密度加大时，温降更为显著，1.4W/cm²热流密度、6kV电压下温降可达到30℃以上。温降的增加反映了电场对微槽的强化润湿进一步提升了微槽换热性能，且电场对较高热流情形下的微槽换热有着更为显著的强化效果。     

Experimental and numerical analysis of the influence of cable tray arrangements on the resulting mass loss rate and fire spreading

In the context of industrial buildings and power plants, electrical installations and cable trays represent a main fuel load and a potential initial fire source due to possible short circuits or comparable malfunction. Furthermore, a fire can spread from one tray to additional trays mounted above and/or horizontally on one tray. Because of the high significance of cable fires, several research projects have been carried out, investigating the fire behaviour of cables from small‐scale tests, eg, the cone calorimeter, up to large‐scale tests, analysing complete cable tray constructions. The goal of the work presented in this paper is the extension of the knowledge regarding the influence of geometrical parameters like the packing density and tray distance on the burning behaviour and fire spread of cable tray installations. The results are considered, together with test results from the literature, to quantify the main physical parameters describing the burning behaviour. In a next step, the general applicability of these parameters as input data for the parametrization of the source term of numerical simulations is shown. The test results show that the burning behaviour and the fire spreading highly depend on the cable arrangement of the cables on the cable tray, in combination with other boundary conditions. By applying the results as input for a fire simulation, the mass loss rate is considered appropriately.     

一种汽车顶盖抗雪压动态仿真分析方法

目前顶盖雪压静态仿真分析方法的雪压计算值与测试值存在偏差,并且不能反映顶盖实际变形的位置和整体变形模式。为改进静态仿真分析方法,提出一种非线性显式计算的动态仿真分析方法,并以某乘用车为例,通过试验验证了其可靠性及有效性,为顶盖的研发设计提供了参考。     

基于密闭爆发器试验的发射装药内弹道性能预估

为了预估发射装药的内弹道性能,建立了一种基于密闭爆发器试验检测发射药的静态燃烧性能参数进而预测其装药内弹道性能的方法,采用不同批次的单樟-5/7发射药进行了装药性能预估计算,并基于30 mm火炮对内弹道性能预估精度进行了试验验证。结果表明,采用所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法计算获得的最大膛压为376.0 MPa,与试验测试的膛压平均值388.7 MPa的计算误差为3.27%;计算的炮口初速为1143.5 m/s,与试验测试的炮口初速平均值1156.3 m/s的计算误差为1.11%。所建立的基于密闭爆发器试验的发射装药内弹道性能预估方法具有较高的精度,可对发射药样品不同批次间的内弹道性能进行高效精确的预估,为长期贮存发射药使用寿命的判定及发射药产品的出厂校验提供了一种高效低成本的弹道性能评价方法。     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

矿用无人卡车国内外研究现状及关键技术

分析了国内外露天矿山用卡车无人驾驶技术发展现状,详细介绍了露天矿山卡车无人驾驶关键技术;通过分析对比前装线控和后装线控两种技术路线的优缺点以及超声波雷达、毫米波雷达、激光雷达、4D光场智能感知系统、红外传感器、视觉传感器等环境感知技术的优缺点;提出多传感器高度融合将是露天矿山卡车实现全天候环境感知的发展方向。通过分析对比惯性导航系统、GNSS差分定位技术、车联网定位技术、电子地图定位技术、视觉传感器等定位导航技术的差异,指出多定位技术融合是露天矿山无人驾驶卡车定位方式的必然选择。结合露天煤矿的生产实际,提出将现有的无人驾驶各种技术算法与露天矿山标准作业流程有机融合是实现卡车无人驾驶的必由之路。最后指出无人驾驶卡车应用5G技术是露天矿山安全生产的关键和核心,是无人驾驶的必备技术。     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

基于步冷试验的2.25Cr-1Mo-0.25V钢母材及焊缝回火脆化研究

对原始态、步冷态、脱脆态和脱脆步冷态2.25Cr-1Mo-0.25V钢母材及焊缝冲击试验结果进行分析,得到了母材和焊缝在不同状态下的韧脆转变温度vTr54.2和FATT以及脆化度ΔvTr54.2和ΔFATT。试验结果表明,步冷试验之后,母材发生较低程度脆化或脱脆现象,但是脆化度或脱脆度较低,表明母材具有良好的抗回火脆化性能;经脱脆试验后,母材和焊缝都发生较高程度的脱脆,表明材料的脆化主要是由于回火脆化引起的,脱脆试验使得材料的韧脆转变温度降低;脱脆步冷试验后,焊缝发生较高程度的脆化,焊缝对脱脆步冷试验的敏感性较高,脱脆步冷试验有效促进了焊缝的脆化。在相同脆化条件下,母材的脆化敏感性低于焊缝,焊缝更易发生脆化。     

Impact of an Engineered Copper-Titanium Dioxide Nanocomposite and Parent Substrates on the Bacteria Viability,Antioxidant Enzymes and Fatty Acid Profiling

Due to the systematic increase in the production of nanomaterials (NMs) and their applications in many areas of life, issues associated with their toxicity are inevitable. In particular, the performance of heterogeneous NMs, such as nanocomposites (NCs), is unpredictable as they may inherit the properties of their individual components. Therefore, the purpose of this work was to assess the biological activity of newly synthesized Cu/TiO₂-NC and the parent nanoparticle substrates Cu-NPs and TiO₂-NPs on the bacterial viability, antioxidant potential and fatty acid composition of the reference Escherichia coli and Bacillus subtilis strains. Based on the toxicological parameters, it was found that B. subtilis was more sensitive to NMs than E. coli. Furthermore, Cu/TiO₂-NC and Cu-NPs had an opposite effect on both strains, while TiO₂-NPs had a comparable mode of action. Simultaneously, the tested strains exhibited varied responses of the antioxidant enzymes after exposure to the NMs, with Cu-NPs having the strongest impact on their activity. The most considerable alternations in the fatty acid profiles were found after the bacteria were exposed to Cu/TiO₂-NC and Cu-NPs. Microscopic images indicated distinct interactions of the NMs with the bacterial outer layers, especially in regard to B. subtilis. Cu/TiO₂-NC generally proved to have less distinctive antimicrobial properties on B. subtilis than E. coli compared to its parent components. Presumably, the biocidal effects of the tested NMs can be attributed to the induction of oxidative stress, the release of metal ions and specific electrochemical interactions with the bacterial cells.