Toughness enhancement and equivalent initial fracture toughness of cementitious composite reinforced with aligned steel fibres

Based on theoretical analysis and numerical simulation, the impact of steel fibres on the stress intensity factor (SIF) at the crack tip for cementitious composite was studied. The enhanced toughness of steel fibre reinforced cementitious composite (SFRC) in resisting cracks was explained by the decrement of SIF caused by steel fibre inclusions at the crack tip of the composite. The equivalent initial fracture toughness was used to characterize the crack initiation of SFRC. A simplified method for determining the of SFRC was proposed based on a linear regression method. Fracture tests were conducted on three‐point bending notched beams with different steel fibre volume fractions and specimen sizes to study the crack initiation behaviour of aligned steel fibre reinforced cementitious composite (ASFRC). of ASFRC was calculated, and the size effect of was analysed. The results showed that slightly increased with the steel fibre volume fraction and gradually became stable. For the tested specimens, whose heights varied between 40 and 100 mm, the specimen size had little impact on the .     

电磁精细探测法在隐伏型导水地质裂缝勘探中的应用

针对传统隐伏型导水地质裂缝勘探方法存在勘测精度较差的问题,提出电磁精细探测法探析隐伏型导水地质裂缝。依照屏蔽系数、实测场强和理论场强数据绘制综合曲线图,通过该图获取隐伏型导水地质裂缝所处位置几何阴影范围,采用层析成像法得到网格化的工作面,获取隐伏型导水地质图像。通过图像直接观测隐伏型导水地质工作面裂缝所处位置,在此基础上,观测四个电磁场分量,采用正交电磁场分量计算介质视电阻率,依据计算视电阻率数值和视电阻率分布状态研究裂缝发育情况和裂缝富水程度。结果表明:采用该方法能较为精准地获取隐伏型导水地质裂缝位置。通过裂缝位置进一步检测出隐伏型导水地质裂缝最大发育高度为63.5 m。当视电阻数值不断增加时,隐伏型导水地质裂缝和裂缝富水性逐渐减小,与实际情况较为相符,说明该种方法探析效果较好。     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

多元合金化大断面球墨铸铁组织和性能的分析

为了提升大断面球墨铸铁综合力学性能，通过复合添加微量合金元素铜、锑、锡、钼对大断面球墨铸铁进行微合金化处理，借助金相显微镜(OM)、扫描电子显微镜(SEM)及力学性能测试等手段，研究了Cu Sb Sn Mo复合微合金化大断面球墨铸铁微观组织和力学性能。结果表明，试验球墨铸铁具有良好的综合力学性能。大断面球墨铸铁中添加铜、锑、锡、钼后优化了材料的组织结构，基体组织为珠光体＋少量牛眼状铁素体；试样石墨组织细小、圆整，分布均匀。同时，合金元素的复合加入使得其抗拉强度达到800 MPa以上，硬度约为280HB，伸长率达到5%以上。拉伸断口分析表明，微合金化大断面球墨铸铁断裂模式以解理断裂为主，伴有少量的塑性变形。     

A simple model for deep dynamic stall conditions

The present study is focused on modeling of dynamic stall behavior of a pitching airfoil. The deep stall regime is in particular considered. A model is proposed, which has a low implementation and computational complexity but yet is able to deal with different types of dynamic stall conditions, including those characterized by multiple vortex shedding at the airfoil leading edge. The proposed model is appraised against an extensive data set of experimental (α,C_L) curves for NACA0012. The results of an existing widely used model, having comparable complexity, are also shown for comparison. The proposed model is able to well reproduce not only the classic curves of deep dynamic stall but also the curves characterized by lift oscillations at high angles of attack due to the shedding of multiple vortices. Furthermore, the model appears to be robust to variations of its parameters from the optimal values and of the airfoil geometry. Finally, the model is successfully implemented in a commercial CFD software and applied to the simulation of a vertical axis wind turbine within the actuator cylinder approach. The accuracy of the prediction of the turbine power coefficient in the whole rotation cycle is very good for the optimal working condition of the turbine, for which the model parameters were calibrated. Fairly good accuracy is also obtained in significantly different working conditions without any further calibration.     

Automated classification of simulated wind field patterns from multiphysics ensemble forecasts

In this study, we have proposed an automated classification approach to identify meaningful patterns in wind field data. Utilizing an extensive simulated wind database, we have demonstrated that the proposed approach can identify low‐level jets, near‐uniform profiles, and other patterns in a reliable manner. We have studied the dependence of these wind profile patterns on locations (eg, offshore vs onshore), seasons, and diurnal cycles. Furthermore, we have found that the probability distributions of some of the patterns depend on the underlying planetary boundary layer schemes in a significant way. The future potential of the proposed approach in wind resource assessment and, more generally, in mesoscale model parameterization improvement is touched upon in this paper.     

Notch radius effect on fracture toughness of ceramics pertinent to grain size

Unlike fracture toughness, the notch fracture toughness of a ceramic is not a constant; rather, it increases with the notch-root radius ρ in a notched specimen. In this study, by analyzing the fracture measurements of eight different notched ceramics with an average grain size G of 3–40 μm, a simple model describing the relation between the notch fracture toughness and fracture toughness is proposed as a function of the relative notch-root radius ρ/G. The normal distribution is incorporated to consider the inevitable scatter in measurements where fracture mechanisms and errors are present. The results demonstrate that the model can effectively predict the quasi-brittle fracture variation trend for ceramics, including the upper and lower bounds, with 96% reliability, from a normal distribution; thus, it can address virtually all of the experimental data. We also determined that the notch fracture toughness approximates the fracture toughness if ρ ≤ G.     

铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。