Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

Sputtered Ir–Ru based catalysts for oxygen evolution reaction: Study of iridium effect on stability

Magnetron sputtered low-loading iridium-ruthenium thin films are investigated as catalysts for the Oxygen Evolution Reaction at the anode of the Proton Exchange Membrane Water Electrolyzer. Electrochemical performance of 50 nm thin catalysts (Ir pure, Ir–Ru 1:1, Ir–Ru 1:3, Ru pure) is tested in a Rotating Disk Electrode. Corresponding Tafel slopes are measured before and after the CV-based procedure to compare the activity and stability of prepared compounds. Calculated activities prior to the procedure confirm higher activity of ruthenium-containing catalysts (Ru pure > Ir–Ru 1:3 > Ir–Ru 1:1 > Ir pure). However, after the procedure a higher activity and less degradation of Ir–Ru 1:3 is observed, compared to Ir–Ru 1:1, i.e. the sample with a higher amount of unstable ruthenium performs better. This contradicts the expected behavior of the catalyst. The comprehensive chemical and structural analysis unravels that the stability of Ir–Ru 1:3 sample is connected to RuO₂ chemical state and hcp structure. Obtained results are confirmed by measuring current densities in a single cell.     

破损水文观测孔涌水封堵技术在高河矿的应用

针对高河矿奥灰水文观测孔空水管锈蚀断裂漏水严重的问题,分析了存在的问题,制定了钻孔涌水封堵技术方案及相应的注浆施工工艺,并进行了为期7天的井下试验。封堵注浆压力达到6 MPa,使用注浆水泥50 t,水泥浆液凝固良好,注浆阀门打开后无出水现象。     

油藏中后期减氧空气驱提高采收率机理研究

尕斯库勒油田E¹₃油藏已经进入高含水时期，储采失衡加剧，综合含水率达到了80%以上，原油产量下降，经济效益变差。为了提高油藏原油采出程度、改善油藏开发效果，调研了国内外减氧空气驱的机理研究以及现场试验的资料，建立了以油藏真实孔渗饱数据为基础的一维条形地层机理模型，并选取该油藏Y12-27井组进行了减氧空气驱可行性验证。研究表明:纵向顶部减氧空气驱驱油效果优于水驱和氮气驱；驱替压力对原油采出程度影响不大；注水转注气可以提高原油采出程度；对于减氧空气驱，由于低温氧化反应的作用，氧气浓度对原油采出程度有一定影响，但比较微弱，其中，氧气浓度为10%时，驱替结束采出程度最高；尕斯库勒油田E¹₃油藏属于注水开发“双高”油藏，适用于减氧空气驱；对于该油藏Y12-27井组，顶部减氧空气驱驱油效果好于水驱和氮气驱，建议氧气浓度超过10%时采取关井等措施。     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Mesoporous g-C3N4 decorated by Ni2P nanoparticles and CdS nanorods together for enhancing photocatalytic hydrogen evolution

Ni₂P nanoparticles and CdS nanorods were grew together on a mesoporous g-C₃N₄ through a facile in-situ solvothermal approach. Under visible light (λ > 400 nm), the as-prepared ternary PCN–CdS-5% Ni₂P composite displays a high H₂ evolution rate with 2905.86 μmol g^?1 h^?1, which is about 14, 18 and 279 times that of PCN–CdS, PCN–Ni₂P and PCN, respectively. The enhanced photocatalytic activity is mainly attributed to the improved separation efficiency of the photocarriers by the type II PCN–CdS heterojunction and the effective extraction of photogenerated electrons by Ni₂P. Meanwhile, Ni₂P acts as co-catalyst to provide the photocatalytic active site for hydrogen reduction. In addition, PCN–CdS-5% Ni₂P composite exerts good stability in 12-h cycles.     

Recent Advances in Conjugated Polymers for Visible-Light-Driven Water Splitting

With the ambition of solving the challenges of the shortage of fossil fuels and their associated environmental pollution, visible-light-driven splitting of water into hydrogen and oxygen using semiconductor photocatalysts has emerged as a promising technology to provide environmentally friendly energy vectors. Among the current library of developed photocatalysts, organic conjugated polymers present unique advantages of sufficient light-absorption efficiency, excellent stability, tunable electronic properties, and economic applicability. As a class of rising photocatalysts, organic conjugated polymers offer high flexibility in tuning the framework of the backbone and porosity to fulfill the requirements for photocatalytic applications. In the past decade, significant progress has been made in visible-light-driven water splitting employing organic conjugated polymers. The recent development of the structural design principles of organic conjugated polymers (including linear, crosslinked, and supramolecular self-assembled polymers) toward efficient photocatalytic hydrogen evolution, oxygen evolution, and overall water splitting is described, thus providing a comprehensive reference for the field. Finally, current challenges and perspectives are also discussed.