Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

一例带电水冲洗触发的220kV避雷器爆炸事故分析

对一例220 kV金属氧化物避雷器在带电水冲洗后发生爆炸故障的原因进行了分析。通过对完好避雷器和故障避雷器进行解体和对比分析,发现故障避雷器下节顶部压力释放装置内部的密封胶圈发生凹陷变形。最后,对该类事故提出预防措施。     

不同含量低污染水对人工湿地中细菌的影响研究

探究水平流人工湿地(HFCW)系统处理低污染水过程中,相同COD/ρ(TN)下不同碳氮含量对细菌群落结构的影响。结果表明,进水为较高碳氮含量的HFCW(HF1)和进水为较低碳氮含量的HFCW(HF2)对COD和TN的去除效率具有一定的差异,HF1和HF2对COD的去除效率分别为48.26%和28.89%,对TN的去除率分别为79.06%和81.87%。HF1中细菌的丰富度和多样性均高于HF2,HF1中富集的优势细菌为Chloroflexaceae、Comamonadaceae和Rhodocyclaceae,均具有异养反硝化功能,HF2中富集的优势细菌为Xanthomonadaceae和Rhodocyclaceae,其中Xanthomonadaceae具有自养反硝化功能。COD、NH4^+-N和NO3^--N对HF1中细菌群落的影响大于对HF2中细菌群落的影响,HF1中COD对细菌群落的影响大于NH4^+-N和NO3^--N。     

某铁矿隔水护顶矿柱厚度计算及安全影响预测

科学合理地确定矿山隔水护顶矿柱安全厚度是矿山安全生产的前提条件，为保障某铁矿地表民房、道路等建（构）筑物安全，防止矿山开采过程中产生的导水裂隙带贯通第四系含水层，采用荷载传递交汇线法、K.B.鲁别涅依他估算法和冒落带、导水裂隙带高度估算法3种理论分析方法对隔水护顶矿柱厚度进行计算，并利用数值模拟手段对留设隔水护顶矿柱后的开采过程安全影响进行了分析，对理论计算结果进行了验证。3种理论计算方法得出的隔水护顶矿柱厚度分别为14.3～17.3 m、17.5～31.4 m和41.8～57.4 m，推荐隔水护顶矿柱留设厚度为60 m。通过数值模拟分析得出，在留设60 m厚的隔水护顶矿柱的基础上，开采区域和隔水护顶矿柱位置产生的最大拉应力约0.47 MPa，矿山开采不会对隔水护顶矿柱造成破坏；地表产生的最大水平位移约5.8 cm，最大垂直位移约26.5 cm，最大倾斜为1.70 mm/m，最大曲率为0.20 mm/m2，最大水平变形值为0.70 mm/m，满足相关规范要求，预测矿山开采不会造成地表建（构）筑物破坏。     

浅谈氯碱氢的一种深度脱水工艺

概述了氢的主要工业生产方法和实际应用,详细介绍了氯碱氢三级脱水工艺过程,并运用在线分析手段,准确显示了干燥过程中的氯碱氢水分含量变化规律。     

Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

基于二元水循环的水量-水质-水效联合调控模型开发与应用

为将我国最严格水资源管理制度的实践与二元水循环理论相结合，提高“三条红线”控制指标的科学性与合理性，本文以SWAT模型为基础，通过改进子流域划分方法、添加经济社会模块和人工用水模块，对其人工侧支循环模拟进行了系统的完善，开发了基于SWAT的水量-水质-水效联合调控模型SWAT_WAQER。以广西南流江流域为例，从国民经济用水量、河道径流与水质等方面对模型进行校验，并在此基础上划分了2030年“三条红线”控制指标。结果表明：该模型性能良好，能够用于不同节水情景下的国民经济用水量、污染物排放量、水功能区水质达标结果分析，可以作为科学制定“三条红线”控制指标的有力支撑工具。     

新型低GWP高温热泵工质HFO-1234ze(Z)的研究进展

高温热泵可以有效回收工业余热，达到节能减排和保护环境的目的。目前，有关高温热泵技术的研究热点在于寻找一种全球变暖潜能值(GWP)低、使用性能良好的工质，以替代现有CFC-114、HFC-245fa工质。对新型环境友好型工质HFO-1234ze(Z)进行了综述，其GWP＜1，临界温度高于423 K，是一种潜在的高温热泵替代工质。总结了近年来国内外学者对HFO-1234ze(Z)的合成技术、热力学性质、输运性质、传热性能等方面的研究，并分析了HFO-1234ze(Z)在高温热泵系统中应用的可行性，认为HFO-1234ze(Z)在高温热泵中具有较好的工作性能和发展前景。