Incoloy 800H合金的应用和性能分析

通过对耐热耐蚀合金Incoloy 80 0H的性能分析 ,指出它与普通奥氏体不锈钢相比具有较优的抗氧化性能、耐蚀性和高温蠕变强度。针对催化裂化装置同轴式沉降再生器内部所用Incoloy 80 0H焊件易出现裂纹的问题进行分析 ,认为在施焊过程中由于合金凝固时有低熔点金属或化合物的液态膜残留在晶界区 ,该合金具有高的焊接热裂纹敏感性 ,若焊材选择不当 ,焊丝填充不充分、缺少保护气等将导致晶间裂纹产生。提出了该合金采用TIG焊接防止热裂纹产生的措施。     

混凝土小型砌块建筑裂缝宽度的标准设置研究

通过对混凝土小型空心砌块单片墙进行试验 ,了解不同构造措施墙体的初始裂缝在墙体上出现的部位、形态、发展规律以及墙体最终破坏形态 ,并通过试验明确墙体在不同受力状态下的裂缝形态 ,最后根据试验结果初步提出混凝土小型空心砌块建筑的裂缝宽度控制标准     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

锈蚀钢筋混凝土结构防护与加固

根据锈蚀钢筋混凝土结构破坏的原因与机理 ,对加固工程界热点问题 ,锈蚀结构防护技术 :阴极保护法 ,设计特点、施工方法、应用范围、阴极电流密度、选择阳极材料等问题进行分析与对比 ;锈蚀结构加固技术 :碳纤维布加固 ,论述其技术要领及破坏特点 ,并推出锈蚀结构受弯构件碳纤维布加固的计算公式     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

摩擦强度对薄膜表面形态的作用:原子力显微镜下的观察

展示了摩擦强度对聚酰亚胺薄膜表面形态的影响，原子力显微图像显示，机械摩擦会使聚酰亚胺薄膜表面上形成微沟槽，这些沟槽的表面具有丰富的表面精细构造。原子显微图像还揭示了机械摩擦可以改变被磨擦聚酰亚胺膜的表面形态。     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

WIN32线程同步方法分析与实现

文章分析了WIN32线程同步的一般方法，并提出了一种的经实践证实也是切实可行线的线程同步方法。