流量自动控制的设计与实现

文章通过分析多相流模拟井的实际工作要求 ,提出了简单实用的流量自动控制模型。应用成型的计算机数据采集和控制模块及稳定可靠的流量控制部件 ,实现了各相流量的自动控制过程。该流量自动控制系统调节精度高、速度快、整体造价低 ,在实际应用中取得了良好的效果。     

长距离油、气、水混输管道内壁流动腐蚀的研究进展

就近几十年来，多相流管线的流动腐蚀（CO2腐蚀，H2S腐蚀，腐蚀/冲蚀协同作用），腐蚀/冲蚀数学模型和设计准则，腐蚀检测，腐蚀防护与控制技术等方面的研究进展进行了综述。指出了当前研究中所存在的一些问题，就多相流的研究方向提出了相应的建议。     

武钢热轧厂层流冷却系统改造及节能效果

针对武钢热轧厂层流冷却系统能耗高，水压不稳，系统反应慢，供水泵工作效率低等缺陷，进行系统改造。提高了系统的控制精度和产品质量，节能降耗取得了明显的效果。     

佛山市中心组团桥梁群对河道影响的数值分析

在不同频率流量和阻水程度条件下,采用一维明渠非恒定流网河数学模型,分析规划中的佛山市桥梁群对区间河道洪季行洪、枯季水环境的影响,计算洪季不同频率洪峰流量下规划桥梁群对区间河道行洪洪水位、分流比的影响,枯季时规划桥梁群对区间河道过流量、分流比的影响,结果表明,利用一维网河数学模型计算佛山市中心组团规划桥梁群对区间河道断面平均水位、流量和流速的影响,结果有足够的数值精度,是可信的。     

Motion and structure interpretation of an optical switch

This paper focuses on tracking, reconstruction and motion estimation of a well-defined MEMS optical switch from a microscopic view. For out-of-view reconstruction, a homography capable of transforming feature points and feature lines between a microscopic image and a CAD model of the switch is implemented. The homography between two sequential microscopic images is decomposed and factorized for motion estimation. Optical flow has also been explored to provide rough estimations of rotation centre and angle. The paper also illustrates motion parameter optimization principles to deal with uncertainty inherent in micro world. After non-linear optimization, estimation accuracy for rotation angle and rotation centre can reach 0.06° and pixel level, respectively.     

Salt-water up-coning during extraction of fresh water from a tropical island

Rainwater can collect in a lens-shaped region within the rock of a tropical island, and may be separated from the underlying salt water by a sharp interface. This paper presents a nonlinear theory for determining the shape of this interface. The island is assumed to be saturated with rain, and provision is made for the outflow of rain-water through the sides of the island. The effect of a bore well on the shape of the interface is investigated, and the problem is solved using a spectral method. An integral-equation method is also presented for the case when the island has infinite width.     

黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Effect of flow on solutions of rod-coil block co-polymers

An elongational flow field is imposed on a solution of block copolymers consisting of semirigid macromolecules with rigid, rodlike sequences of units in combination with random coil (flexible) units. The problem is formulated according to the lattice treatment of Matheson and Flory. In this formulation, the system consists of rigid blocks whose lengths and locations are fixed by the structure within each macromolecule. These blocks are separated by random coiled units. An excess free energy other than the equilibrium Gibbs free energy of the quiescent solution has to be considered due to the flow field that tends to align the rods. This excess free energy is calculated from the potential energy of rods when a steady-state, homogeneous and irrotational flow field is applied to the solution. The effects of composition, polymer-solvent interaction, size of the co-polymer and flow rates are investigated. Depending on the size and number of rods, some of the chains studied exhibit a biphasic region at equilibrium that shifts to lower concentrations with increasing flow. Longer chains with shorter rods that are isotropic at equilibrium, exhibit a biphasic region at finite values of flow. The degree of orientation increases sharply when the system is biphasic. For larger flows, the orientation function is very close to unity which is perfect orientation.     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.