聚合物/蒙脱土纳米复合材料的制备与结晶性能

本文综述了制备聚合物 /蒙脱土纳米复合材料的插层方法 ,并对有代表性的结晶性聚合物 /蒙脱土纳米复合材料的结晶性能进行了讨论。蒙脱土的加入对聚合物的结晶有两种作用 ,一方面是对聚合物有异相成核的作用 ,可以提高聚合物的结晶温度和结晶速率 ,降低结晶活化能 ;另一方面是对聚合物结晶生长有阻碍作用 ,导致结晶速率下降 ,结晶活化能提高     

振动力场作用下聚合物挤出制品结构与性能的质量控制与优化

利用实验数据，分析与研究振动场振动参数对聚合物挤出制品质量的影响，对聚合物挤出制品的熔体流动速率，微晶结构，拉伸强度等主要性能质量指标，建立以振动频率为主要控制变量的神经网络模型，并引入信息分配模型，探讨了一个网络输入节点下神经网络学习样本的特征提取与优化。实验结果表明，经过信息预处理的学习样本，可以使网络有更好的收敛效果。     

南水北调西线工程可调水量分析

在受水区缺水形势严峻的情况下，引水工程可调水量的确定主要与三个因素有关：一是引水河流及引水坝址径流量；二是坝址上下游用水要求；三是引水水库工程规模。在考虑各种因素影响后，提出各引水坝址可调水量占坝比径流量的比例在70％左右比较合适，按现阶段推荐的两种方案，可调水量可达160亿－170亿m^3.     

Network topology and the theory of rubber elasticity

The earliest investigations on rubber elasticity, commencing in the 19th century, were necessarily limited to phenomenological interpretations. The realisation that polymers consist of very long molecular chains. commencing c. 1930, gave impetus to the molecular theory of rubber elasticity (1932-). according to which the high deformability of an elastomer, and the elastic force generated by deformation, stem from the configurations accessible to long molecular chains. Theories of rubber elasticity put forward from 1934-1946 relied on the assumption that the junctions of the rubber network undergo displacements that are affine in macroscopic strain. The theory of James and Guth (1947) dispensed with this premise, and demonstrated instead that the mean positions of the junctions of a ‘phantom’ network consisting of Gaussian chains devoid of material properties are affine in the strain. The vital significance of the distinction between the actual distribution of chain vectors in a network and their distribution if the junctions would be fixed at their mean positions went unnoticed for nearly 30 years. Experimental investigations, commencing with the incisive work of Gee in 1946. revealed large departures from the relationship of stress to strain predicted by the theories cited. This discrepancy prompted extensive studies, theoretical and experimental, during succeeding years. Inquiry into the fundamentals of polymer networks, formed for example by interlinking very long polymer molecules, exposed the need to take account of network imperfections, typically consisting of chains attached at only one end to a network junction. Various means were advocated to make corrections for these imperfections. The cycle rank ζ of the network has been shown (1976) to be the fundamental measure of its connectivity, regardless of the junction functionality and pattern of imperfections. Often overlooked is the copious interpenetration of the chains comprising typical elastomeric networks. Theories that attempt to represent such networks on a lattice are incompatible with this universal feature. Moreover, the dense interpenetration of chains may limit the ability of junctions in real networks to accommodate the fluctuations envisaged in the theory of phantom networks. It was suggested in 1975 that departures from the form predicted for the elastic equation of state are due to constraints on the fluctuations of junctions whose effect diminishes with deformation and with dilation. Formulation of a self-consistent theory based on this suggestion required recognition of the non-affine connection between the chain vector distribution function and the macroscopic strain in a real network, which may partake of characteristics of a phantom network in some degree. Implementation of the idea was achieved through postulation of domains of constraint affecting the equilibrium distribution of fluctuations of network junctions from their mean positions. This led in due course to a theory that accounts for the relationship of stress to strain virtually throughout the ranges of strain accessible to measurement. The theory establishes connections between structure and elastic properties. This is achieved with utmost frugality in arbitrary parameters.     

胜利原油350～510℃馏分糠醛精制的研究

对胜利原油 350～ 510℃馏分每 4 0℃切割一种馏分进行糠醛精制 ,考察了实验室条件下不同温度、不同醛油比条件下精制对提余油质量和收率的影响。采用醛油比 3× 1∶1,抽提温度在 70～ 95℃ ,可使精制馏分油粘度指数提高 10～ 2 7个单位 ,精制油收率高于 70 %。     

2.0 Mt/a渣油加氢脱硫装置新氢压缩机性能标定

介绍了中国石化茂名分公司 2 .0Mt/a渣油加氢脱硫装置中的 4M80 30 /2 2 2 0 0 BX型新氢压缩机的特点、技术特征及标定情况。采用国际通用标准对压缩机气体组成、容积流量、轴功率、进排气压力和进排气温度等指标进行了测定。标定表明 ,该机组设计方案合理 ,运转平稳 ,性能指标达到设计要求 ,较好的满足了工艺操作的需要     

光漂白法制备有机聚合物非线性定向耦合器

研究了用光漂白的方法制备PMMA/DR1聚合物非线性定向耦合器,提出了一种容易的制备方法来得到要求的耦合长度.测量了材料的光学非线性对定向耦合器两臂透过率的影响.实验结果表明由于光学非线性,耦合器的耦合长度随着入射光强度的改变而发生变化.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

高分子纳米LB膜的制备及其光刻性能研究

合成并表征了N-十六烷基丙烯酰胺（HDA）和对叔丁基苯酚甲基丙烯酸酯（BPhMA）的共聚物p（HDA-BPhMA）s。当HDA含量较高时，共聚物可在气，液界面上形成稳定，排列紧密的单分子薄膜，并可以Y型膜的方式沉积在各种固体基片上，形成多层均匀的Langrnuir-Blodgett（LB）膜。这种LB膜被成功地应用于光刻，获得了分辨率为0.5μm的LB膜图形。以该图形为抗蚀层，可将图形进一步转移至金属薄膜上，得到分辨率较高的金属图形，在图形转移的过程中，这种LB膜显示出较高的抗蚀性，有望作为纳米抗蚀薄膜材料在亚微米刻蚀领域得到应用。