Finite element analysis of fracture behavior in ceramics: Competition between artificial notch and internal defects under three-point bending

Evaluation of the nonlinear relationship between the surface defect size and fracture strength of ceramics is important for engineering applications. In this study, we aim to predict the apparent nonlinear relationship between the defect size and fracture strength of single-edge notched beams (SENBs) using the finite element method. Specifically, we applied the methodology for predicting fracture strength from microstructure distribution data (relative density, pore size, aspect ratio, and grain size) to a finite element analysis (FEA) model in which the shape and size of the initial defects are defined at notch locations. By reproducing the apparent nonlinearity caused by the competition between the surface and internal defects within the framework of linear elastic fracture mechanics, the effectiveness of the FEA methodology for the evaluation of strength scatter and allowable crack size in ceramics was demonstrated.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。     

非全日制研究生线上线下混合式教学模式研究 ——以《现代电气控制技术》为例

随着教育信息化技术的发展，线上线下混合式教学模式已成为一种趋势。为了解决非全日制研究生课堂教学召集困难、效果不佳等问题，提出了基于“互联网＋虚拟仿真技术”的线上线下混合式教学模式。本文以控制工程专业学位研究生为例，结合《现代电气控制技术》课程，探讨了线上线下混合式教学实现途径、师生互动方法、项目驱动案例教学法以及电气控制系统虚拟仿真实验平台的构建方法，切实提升非全日制研究生的培养质量。     

Event-triggered distributed receding horizon control for tracking and formation of homogeneous multi-agent systems

This paper proposes an event-triggered distributed receding horizon control (DRHC) approach for the formation and tracking problems of homogeneous multi-agent systems. For each agent, an event-triggering condition, based on assumed predictive information of the neighbours, is derived from stability analysis. Considering the uncertain deviation between the assumed and true predictive information, we design a time-varying compatibility constraint for the individual optimization problem. In the event-triggered DRHC algorithm, each agent solves the optimization problem and communicates with its neighbours only when the event-triggering condition is satisfied, so the communication and computation burden are reduced. Moreover, guarantees for the recursive feasibility and asymptotic stability of the overall system are proved. A simulation example is provided to illustrate effectiveness of the proposed approach.     

Sensitization of MCF7 Cells with High Notch1 Activity by Cisplatin and Histone Deacetylase Inhibitors Applied Together

Histone deacetylase inhibitors (HDIs) are promising anti-cancer agents that inhibit proliferation of many types of cancer cells including breast carcinoma (BC) cells. In the present study, we investigated the influence of the Notch1 activity level on the pharmacological interaction between cisplatin (CDDP) and two HDIs, valproic acid (VPA) and suberoylanilide hydroxamic acid (SAHA, vorinostat), in luminal-like BC cells. The type of drug–drug interaction between CDDP and HDIs was determined by isobolographic analysis. MCF7 cells were genetically modified to express differential levels of Notch1 activity. The cytotoxic effect of SAHA or VPA was higher on cells with decreased Notch1 activity and lower for cells with increased Notch1 activity than native BC cells. The isobolographic analysis demonstrated that combinations of CDDP with SAHA or VPA at a fixed ratio of 1:1 exerted additive or additive with tendency toward synergism interactions. Therefore, treatment of CDDP with HDIs could be used to optimize a combined therapy based on CDDP against Notch1-altered luminal BC. In conclusion, the combined therapy of HDIs and CDDP may be a promising therapeutic tool in the treatment of luminal-type BC with altered Notch1 activity.     

气藏型储气库注气期试井分析探讨

针对气藏型储气库注采井注采过程中储层物性参数影响因素不明确、注采能力不对称的问题。基于相国寺储气库井下连续油管试井测试结果,提出储气库注气期“温降效应”、“变表皮效应”的概念,分析了储气库注采过程中温降效应、变表皮效应以及储层应力敏感对注采的影响。通过气藏型储气库注气期试井分析技术,研究各因素在试井曲线上的响应特征以及对试井解释参数的影响。结果表明:①相对于采气期试井测试,注气期测试得到的储层物性参数具有同样的参考价值;②储气库温降效应对于试井解释结果的影响可忽略不计,而在不同注采运行周期内,变表皮效应以及应力敏感效应影响差异较大;③编制储气库注采运行方案时应充分考虑变表皮效应与应力敏感的影响,在不同注采运行周期内开展试井测试获取准确的储层参数值。研究成果为储气库试井测试与解释提供了重要的研究依据和理论指导。