合成氨扩能改造中锅炉存在的问题及采取的措施

针对天脊集团年产30万t合成氨扩能改造,给2台225t/h高压锅炉带来的除氧器热量过剩、锅炉给水温度升高、主蒸汽温度降低等一系列问题,分析了产生问题的原因,从节约能源、提高锅炉效率考虑,提出了相应的解决问题的办法:利用热量分流、改造省煤器管、增加二级过热器受热面积。经过3年多的生产实践证明,取得了良好的效果。     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Thermal-lens and photo-acoustic methods for the determination of SiC thermal properties

In this paper we report the use of photothermal techniques such as Thermal lens (TL) spectrometry, Photoacoustic and heat capacity, ρc_p, to determine the thermo-optical parameters, such as thermal conductivity (K), thermal diffusivity (D), specific heat (c_p) and the optical path dependence with temperature (ds/dT), of an undoped polycrystalline 3C-SiC. To our knowledge, this is the first time that Thermal lens technique is used for wide band-gap systems. Results obtained for the polycrystalline sample with TL technique indicates that ds/dT is negative at room temperature. Moreover, the obtained values of thermal diffusivity and thermal conductivity are in good agreement with that found in the literature, indicating that the phototermal techniques can be used to obtain the referred parameters in circumstances where other techniques cannot be used, for example, in harsh environments.     

Investigation of the impact of changes in demand forecasting method on the financial performance of an electricity supply undertaking

Peak demand forecasts obtained from six different univariate forecasting methods, under a range of conditions, were used to drive a capacity acquisition model of a large electrical supply system; and the resulting physical and financial performance of the model was observed for each set of forecasts. The results obtained are discussed in the context of their implications for the choice of load forecasting method used in capacity acquisition planning by a power supply undertaking.     

电容传感器在使用中存在的几个问题及处理方法

随着电容测量技术的迅速发展，电容传感器在非电量测量和自动检测中得到广泛应用，但它在使用过程中也存在一些问题，针对在使用电容传感器过程中存在的几个问题，从电容传感器的原理和工作过程两个方面进行了讨论，并提出行之有效的处理方法。     

Reconstruction of Mandibular Defect with Porous β-TCP/BMG Artificial Bone

1Introduction Reconstructivesurgeryisoneofthehottestre searchedsubjectsthatdealingwithbonedefects.Thetra ditionalmethodisimplantationoffreshautograftbonebe causeofitsnon immunoreactiveproperty.Butautologousbonewasnotabundantinsomecases.Sowefoundbeta trica…     

Separating n-alkane mixtures by exploiting differences in the adsorption capacity within cages of CHA, AFX and ERI zeolites

The saturation capacity of n-alkanes in CHA, AFX and ERI zeolites, that consist of cages separated by windows, decreases with increasing carbon number. The major aim of the present communication is to demonstrate the possibility of separating n-alkane mixtures relying on differences in saturation capacities. To investigate this possibility, Configurational-Bias Monte Carlo simulations for adsorption of C3–nC6, nC4–nC6, and nC5–nC6 mixtures in CHA, AFX and ERI were carried out for equimolar bulk fluid phase. These mixture simulations show that for operation at fluid phase fugacities below about 1 MPa, the adsorbed phase in equilibrium with the bulk vapor phase is predominantly the alkane with the longer chain length, i.e. nC6. However, for operation at pressures in excess of 1 MPa, the adsorbed phase in equilibrium with the bulk liquid phase is richer in the component with the smaller chain length. In some cases, the nC6 is practically excluded from the zeolite.     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.