Dhh1 is a member of the SESA network

The correct separation of chromosomes during mitosis is necessary to prevent genetic instability and aneuploidy, which are responsible for cancer and other diseases, and it depends on proper centrosome duplication. In a recent study, we found that Smy2 can suppress the essential role of Mps2 in the insertion of yeast centrosome into the nuclear membrane by interacting with Eap1, Scp160, and Asc1 and designated this network as SESA (S my2, E ap1, S cp160, A sc1). Detailed analysis showed that the SESA network is part of a mechanism which regulates translation of POM34 mRNA. Thus, SESA is a system that suppresses spindle pole body duplication defects by repressing the translation of POM34 mRNA. In this study, we performed a genome-wide screening in order to identify new members of the SESA network and confirmed Dhh1 as a putative member. Dhh1 is a cytoplasmic DEAD-box helicase known to regulate translation. Therefore, we hypothesized that Dhh1 is responsible for the highly selective inhibition of POM34 mRNA by SESA.     

Microwave and conventional treatment of low-cement high-alumina castables with different water-to-cement ratio; Part II. Dehydration

Modern refractory castables contain between 3.5 and 5?wt.-% water that is necessary for sufficient flow during emplacement and for the formation of hydrate phases, necessary for the green strength of the material. Prior to the high temperature use of this material, it must be dried very carefully to avoid explosive spalling.This paper will demonstrate that beside conventional drying of pre-shaped materials in resistance furnaces microwave radiation is an energy saving and rapid method to remove pore water as well as hydrate bond water from the castable. In comparison to resistance furnaces, the use of microwave radiation does not affect the castable properties as there are mechanical strength (MOR, CCS), open porosity and pore size distribution. This study proved microwave radiation as valuable alternative with a series of tabular alumina based low cement castables (LLC) in which the water-to-cement-ratio (wcr = 0.64, 0.75, 0.82 and 1.13) was systematically altered by changing the cement concentration at constant mixing water concentration of 4.5%.     

Hydrogen production through dry reforming of biogas using a porous electrochemical cell: Effects of a cobalt catalyst in the electrode and mixing of air with biogas

This paper reports the performance of porous Gd-doped ceria (GDC) electrochemical cells with Co metal in both electrodes (cell No. 1) and with Ni metal in the cathode and Co metal in the anode (cell No. 2) for CO₂ decomposition, CH₄ decomposition, and the dry reforming reaction of a biogas with CO₂ gas (CH₄ + CO₂ → 2H₂ + 2CO) or with O₂ gas in air (3CH₄ +?1.875CO₂ +?1.314O₂ → 6H₂ +?4.875CO +?0.7515O₂). GDC cell No. 1 produced H₂ gas at formation rates of 0.055 and 0.33?mL-H₂/(min?m²-electrode) per 1?mL-supplied gas/(min?m²-electrode) at 600?°C and 800?°C, respectively, by the reforming of the biogas with CO₂ gas. Similarly, cell No. 2 produced H₂ gas at formation rates of 0.40?mL-H₂/(min?m²) per 1?mL-supplied gas/(min?m²) at 800?°C from a mixture of biogas and CO₂ gas. The dry reforming of a real biogas with CO₂ or O₂ gas at 800?°C proceeded thermodynamically over the Co or Ni metal catalyst in the cathode of the porous GDC cell. Faraday's law controlled the dry reforming rate of the biogas at 600?°C in cell No. 2. This paper also clarifies the influence of carbon deposition, which originates from CH₄ pyrolysis (CH₄ → C + 2H₂) and disproportionation of CO gas (2CO → C + CO₂), on the cell performance during dry reforming. The dry reforming of a biogas with O₂ molecules from air exhibits high durability because of the oxidation of the deposited carbon by supplied air.     

Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 × 2550 × 150 mm³ dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m³) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.     

Tuning effect of silicon substitution on magnetic and high frequency electromagnetic properties of R2Fe17 and their composites

In this work, we report the tuning effect of the Si substitution on the magnetic and high frequency electromagnetic properties of R₂Fe₁₇ compounds and their paraffin composites. It is found that the introduction of Si can remarkably improve the magnetic and electromagnetic properties of the R₂Fe₁₇ compounds, making the R₂Fe_17–xSi_x-paraffin composites excellent microwave absorption materials (MAMs). By introducing the Si element, their saturation magnetizations decrease slightly, while much higher Curie temperatures are obtained. Furthermore, better impedance match is reached due to the decrease of the high-frequency permittivity ε′ by about 40%–50%, which finally enhances the performance of the microwave absorption. The peak frequency (f_RL) of the reflection loss (RL) curve moves toward high frequency domain and the qualified bandwidth (QB, RL ≤ ?10 dB) increases remarkably. The maximum QB of 3.3 GHz (12.0–15.3 GHz) is obtained for the Sm_1.5Y_0.5Fe₁₅Si₂-paraffin composite (d = 1.0 mm) and the maximum RL of ?53.6 dB is achieved for Nd₂Fe₁₅Si₂-paraffin composite (d = 2.2 mm), both surpassing most of the reported MAMs. Additionally, a distinguished dielectric microwave absorption peak is observed, which further increases the QB in these composites.     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。     

带有方形肋及双倾斜肋片的细通道内流动、传热和熵产分析

为了探究带有方形肋及双倾斜肋片细通道的流动换热及熵产特性，设计了2种带有方形肋及双倾斜肋片的组合细通道(MCDS-L, MCDS-R)，然后采用数值模拟的方法分析其流动特性、传热特性和熵产特性，并将其分析结果同2种方形肋细通道(MCS-L, MCS-R)和一种双倾斜肋片细通道(MCD)进行对比。结果表明，在所研究的雷诺数范围内，组合通道的摩擦阻力系数基本一致且均高于其他3组通道(MCS-L, MCS-R, MCD) 。此外，组合通道的努塞尔数均高于其他3组通道，而熵产增大数均低于其他3组通道。其中，MCDS-L通道的努塞尔数最大，熵产增大数最低。表明MCDS-L通道的换热效果最佳，能量的综合利用程度最高。研究成果为微细通道热沉的设计提供参考。     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.     

Pull out of FRP reinforcement from masonry pillars: Experimental and numerical results

In this paper, debonding phenomena between carbon fiber reinforced polymer (CFRP) strips and masonry support were investigated on the basis of single-lap shear tests, considering different dimensions of the bond length. To capture the post-peak response of the CFRP–masonry joint, the slip between the support and the reinforcement strip was controlled using a clip gauge positioned at the end of the reinforcement. The tests were simulated by means of a finite element model able to capture the post-peak snap-back behavior due to the failure process. The numerical model is based on zero-thickness interface elements and on a proper non-linear cohesive law. The comparison between experimental and numerical results was performed in terms of overall response, measured by both the machine stroke and the clip gauge positioned at the free end of the reinforcement. The cases of effective bond length greater and lesser than the minimum anchorage length, suggested by the CNR Italian recommendation, were considered.     

Solidification morphology and phase selection in drop-tube processed Ni–Fe–Si intermetallics

Drop-tube processing was used to rapidly solidify droplets of Ni_64.7Fe₁₀Si_25.3 and Ni_59.7Fe₁₅Si_25.3 alloys. In the larger droplets, and therefore at low cooling rates, only two phases, γ-Ni₃₁Si₁₂ and β₁-Ni₃Si were observed. Conversely, in the smaller droplets, and therefore at higher cooling rates, the metastable phase Ni₂₅Si₉ was also observed. The critical cooling rate for the formation of Ni₂₅Si₉ was estimated as 5 × 10³ K s⁻¹. SEM and TEM analysis reveals three typical microstructures: (I) a regular structure, comprising single-phase γ-Ni₃₁Si₁₂ and a eutectic structure between γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (II) a refined lamellar structure with a lamellar spacing <50 nm comprising γ-Ni₃₁Si₁₂ and β₁-Ni₃Si; (III) an anomalous structure with a matrix of Ni₂₅Si₉ and only a very small proportion of a second, and as yet unidentified, phase. These results indicate that there is an extended stability field for Ni₂₅Si₉ in the Ni-rich part of the Ni–Fe–Si ternary system in comparison to the Ni–Si binary system. With an increase of cooling rate, an increasing fraction of small droplets experience high undercoolings and, therefore, can be undercooled into the Ni₂₅Si₉ stability field forming droplets consisting of only the anomalous structure (III). The Fe atoms are found to occupy different substitutional sites in different phase, i.e. Fe substitutes for Ni in the γ phase and Si in the L1₂ (β₁) phase respectively.