纳米氧化铝的制备及应用

介绍了高科技产品纳米氧化铝的 3大制备方法 :固相法、气相法、液相法的优缺点 ,以及纳米氧化铝的应用与发展前景     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

高炉鼓风机就地扩容改造方案及经济效益

介绍了利用高炉鼓风机基础实施不易地扩容改造的设计工艺方法，该方法不仅降低了设计、施工、安装费用，而且缩短了施工周期，降低了固定资产投资。     

Recent developments of high-performance NEOMAX magnets

For further improvement in achieving extremely high magnetic properties of Nd- Fe- B sintered magnets, extensive investigation has been done to densify the magnet up to the theoretical value, to increase the volume fraction of the Nd ₂Fe₁₄B matrix phase, and to achieve a high degree of alignment. By controlling chemical composition and the amount of constituent phases,improving particle size distribution, and adopting the isostatic pressing method to get better alignment of fine particles, we have succeeded in obtaining a high-performance magnet having residual flux density (B_r) of 1.495 T (14.95 kG), maximum energy product [(BH)_max] of 431 kj/m³ (54.2 MGOe), and intrinsic coercivity (iH_c) of 845 kA/m (10.62 kOe).     

Influence of melt superheat on breakup process of close-coupled gas atomization

In close-coupled gas atomization（CCGA）, the influences of melt superheat on breakup process are fundamental to obtain desired or finer powder. Based on a series of Cu atomization experiment under different superheating conditions, the influences of melt superheat on breakup process were studied. Experimental results indicate that as the melt superheat is increased to 150, 200, 250 and 300 K, the mean particle size （D50） decreases consequently to 34.9, 32.3, 30.9 and 19.7 μm. Theoretical analysis reveals that the primary breakup and secondary breakup processes are close coupled, and the melt superheat radically influences the melt properties, and plays a crucial role on governing the filming process of primary breakup and the atomization modes of secondary breakup. There exists a strong nonlinear decrease of contact angle of melt to nozzle orifice wall when the superheat is increased fi＇om 250 K to 300 K, leading to a marked fall of the film thickness formed in primary breakup, and D50 of copper powders is therefore sharply reduced. However, the log-normal distribution feature of particle size has not been substantially improved.     

A new method of characterization for stratified thermal energy stores

A new method for characterization of stratified thermal energy stores (TES) that integrates both the first law and the second law concerns is presented here. The first law concern is incorporated into a quantity called energy response factor and the second law concern into an entropy generation ratio. A product of these two quantities is at the heart of the TES efficiency definitions. This approach removes the overemphasis of the existing methods either on the first or the second law of thermodynamics which often biases the characterization results. The information about the evolution of the temperature field of the system in time is the prerequisite of the new method. It may be obtained from experiments or from suitable numerical simulations. The current method can be easily integrated into computational fluid dynamic (CFD) simulations and thus facilitate CFD-based design analysis. As an example of such CFD-integrated analysis, a large-scale hot water seasonal heat store is numerically studied to identify the effects of aspect ratio, containment shape, internal structures, and containment size on their efficiency. The results suggest the effectiveness of the new method in deriving useful design insights.     

THE RELATIONSHIP BETWEEN HAZE AND THE SIZE OF PARTICLES IN BEER

Haze measurements have been obtained for suspensions of polystyrenelatex particles of known diameter using two light scattering instruments which measure at angles of 90° and 13° respectively. The results agree well with the theory of light scattering and demonstrate the significant effects of particle size and angle of detection upon the instrumental values for haze. This information has been used to correlate the particle size distributions of a number of beers, as measured by Coulter Counter, with the corresponding, measured haze values.     

回转体拉深件毛坯直径的简捷计算及误差分析

通用的回转体拉深件毛坯直径的计算公式繁琐，不蝗记忆，特别是利用中线尺寸常出现小数点使计算复杂，本文针对此问题分别推导出了利用中线尺寸和不用中线尺寸时，毛坯直径的简捷计算公式。并进行了误差分析，最后用实例对简捷计算方法的正确性给予了验证。     

大中型风力发电机组可靠性研究

研究了大中型风力发电机组的可靠性，讨论了可靠性指标的分配，可靠性设计的四个重要方面、可靠性试验计算机模拟。