陶瓷及陶瓷基复合材料微缺陷的超声检测

为研究陶瓷及陶瓷基复合材料微缺陷的超声检测能力，针对一些人工缺陷试样进行了超声检测试验。试验主要采用了纵波垂直入射法和泄漏瑞利波法。通过试验结果，比较了两种方法的检测能力。     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

从PZT体系看无铅压电陶瓷的可能应用

总结了主要以(Bi0.5Na0.5)TiO3和NaNbO3为基的无铅压电陶瓷的性能，以Pb(Ti，Zr)TiO3基二元系、三元系压电陶瓷的性能与应用为参考，分析了无铅压电陶瓷可能的器件应用。此外，还对拓宽无铅压电陶瓷应用需要改进的性能提出了建议。     

机械力化学作用对低介硅灰石瓷料的相变和相组成的影响

采用X射线衍射仪(XRD)、差热分析(DTA)手段详细研究了由氧化物粉末制备硅灰石陶瓷时,机械力化学作用及后续热处理对硅灰石陶瓷相组成和相变过程的影响,分析了机械力化学在球磨过程中的作用机理主要是细化晶粒、使晶格畸变、晶格缺陷增多、非晶化和诱导低温化学反应。结果表明:高能球磨中的机械力化学作用能够有效地降低硅灰石陶瓷的烧成温度(11160~11220℃)。探明了经高能球磨的样品在烧成过程中的晶相转变规律。瓷料最终的晶相为单一的-硅灰石(高温变体)。     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

晶须取向对SiCw/6061Al复合材料热压缩变形行为的影响

采用SEM 和 Magiscan-2A 图像分析系统研究了晶须取向对SiCw/6061Al复合材料在300℃压缩变形行为的影响.结果表明:晶须取向影响着晶须折断程度和转动角度; 随着晶须取向角的增加,晶须转动和折断行为所导致的软化效果下降.同时晶须取向也影响复合材料的热压缩应力-应变曲线的形状.在热压缩变形过程中,晶须取向角为0°和30°的复合材料表现出明显应变软化现象, 晶须取向角为45°的复合材料无明显软化现象.晶须取向角为90℃的复合材料表现出应变硬化现象.     

多孔无机材料的性质及用途

对各种多孔无机材料的制备工艺原理和性质进行了论述，并分析了影响多孔无机材料孔径的因素，介绍了多孔无机材料在国民经济生产中的各种用途，指出了以往研究发展中存在的问题。     

金属泡沫材料研究进展

综述了金属泡沫材料的各种制备方法。液相法制备金属泡沫材料包括气体吹入法、固体发泡剂法和固体—气体共晶凝固法、熔模铸造法、渗流铸造法、喷射沉积法以及粉末加压熔化法等制备方法。采用金属粉末烧结法、浆料发泡法等制备工艺可以从固相制备金属泡沫材料。电沉积法以及气相沉积法可用于制备高孔隙率的金属泡沫材料。最后简要总结了金属泡沫材料的应用。     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.