Fracture toughness of bisphenol A‐type epoxy resin

The relationship between the postcuring conditions and the fracture toughness of a bisphenol A‐type epoxy resin cured with acid anhydride was investigated. The glass transition temperature and fragility parameter, derived from the thermo‐viscoelasticity, were used to characterize the epoxy resin postcured under various conditions. Relationship between these two parameters and the fracture toughness was then investigated, based on the fractography results of a microscopic roughness examination of a fractured surface. The values of the glass transition temperature and fragility greatly depended on the postcuring conditions. The glass transition temperature was approximately 400 K when the crosslinking reaction was saturated. The fragility was independent of the saturation of the reaction and varied between 50 and 180. The results of the fracture test and fractography examination showed that there was no direct correlation between the glass transition temperature, the fracture toughness, and the roughness. On the other hand, there was a correlation between the fragility, fracture toughness, and roughness when the glass transition temperature saturated (at 400 K). As the fragility decreased from 180 to 50, the fracture toughness increased from 0.6 to 1.1 MPa · m^1/2 at the same glass transition temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 10: 2266–2271, 2002     

Enhanced strain hardening in elongational viscosity for HDPE/crosslinked HDPE blend. I. Characteristics of crosslinked HDPE

Blending a crosslinked high‐density polyethylene (xHDPE) enhances melt strength and strain hardening behavior in elongational viscosity of high‐density polyethylene (HDPE) to a great degree. Gel fraction of xHDPE has a stronger effect on the strain hardening than sol fraction, although sol fraction also enhances the strain hardening to some degree. Further, the xHDPE crosslinked by peroxide in a compression mold exhibits more pronounced effect than xHDPE by radiation, which is attributed to the difference in the amount of the gel fraction. The xHDPE, which enhances the strain hardening, has sparse crosslink points in the network. Moreover, it was found from linear viscoelastic measurements, such as oscillatory modulus and relaxation modulus, that the xHDPE is characterized as a critical gel, which was also supported by the result of tensile testing. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 73–78, 2002     

Influence of untreated and novel electron‐beam‐modified surface‐coated silica filler on the thermorheological properties of ethylene–octene copolymer

We developed surface‐modified silica fillers by coating these with an acrylate monomer, trimethylolpropane triacrylate, or a silane coupling agent, triethoxyvinyl silane, followed by electron‐beam irradiation at room temperature. These were incorporated in an ethylene–octene copolymer rubber. Thermorheological studies of the unvulcanized ethylene–octene copolymer and its untreated and modified silica‐filled composites were done with a shear dynamic oscillating rheometer. Modification of the silica filler, especially via the silanization process followed by electron beam treatment, significantly reduced filler–filler networking as revealed from the log–log plots of storage modulus and complex shear viscosity, and its real component. The rheological complexity of the compositions was analyzed from a double logarithmic plot of the storage modulus and loss modulus. The results obtained from the master curves constructed on the basis of the time–temperature superposition principle and the activation energy calculated from the Arrhenius equation for the flow of above these compounds further supported these findings. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2453–2459, 2003     

Dynamic mechanical properties of styrene‐butadiene rubber vulcanizate filled with electron beam modified surface‐treated dual‐phase filler

The influence of the electron beam modification of a dual‐phase filler on the dynamic mechanical properties of styrene‐butadiene rubber (SBR) is investigated in the presence and absence of trimethylol propane triacrylate or triethoxysilylpropyltetrasulfide. Electron beam modification of the filler results in reduction of the tan δ at 70°C, a parameter for rolling resistance, and an increase in the tan δ at 0°C, a parameter for wet skid resistance of SBR vulcanizates. These modified fillers give significantly better overall performance in comparison with the control dual‐phase filler. This variation in properties is explained in terms of filler parameters such as the filler structure that leads to rubber occlusion and filler networking. These results are further corroborated using the master curves obtained by the time–temperature superposition principle. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2992–3004, 2003     

Viscoelastic and Processing Effects on the Fiber-Matrix Interphase Strength. Part I. The Effects of Loading Rate, Test Temperature, Fiber Sizing and Global Strain Level

The effects of loading rate, fiber sizing, test temperature and global strain level on the adhesion strength between carbon fibers and a thermosetting epoxy (Epon 815) are studied using the single fiber fragmentation test procedure. Analytical methodology describing the viscoelastic behavior observed is also presented. The possibility of rate-temperature-interphase thickness superposition for the interfacial strength function is illustrated based on the analytical models discussed. Experimental data are discussed using Weibull statistics and also presented in the form of percent relative frequency histograms for the fiber fragments in a collective fashion. The use of histograms allows for interpretation of the skewness in the data population.     

Thermally stimulated creep (TSCr) study of viscoelastic behavior and physical aging of a polymeric matrix composite for spacecraft structures

Thermally Stimulated Creep (TSCr) mechanical spectroscopy has been used to analyze molecular movements in KMU‐4lcarbon/epoxy composite material around the glass transition temperature. This technique is powerful to characterize the microstructure and micromechanical properties of the epoxy matrix and their evolution upon thermal aging. Three cooperative submodes have been distinguished by resolving the fine structure of the material complex α‐retardation mode. The elementary processes constituting this mode possess activation enthalpies and preexponential factors that strongly depend on the thermal history of the sample. The activation parameters of the composite are subject to perceptible evolution due to postcuring degradation. The α‐mode associated complex spectrum shifts towards higher temperatures by 27°C as a consequence of a series of quenching in the temperature range 260 to 0°C; the material shows a rise in the fragility and a deterioration in the crack‐growth resistance qualities. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 342–350, 2002     

Dynamic viscoelasticity of low‐density polyethylene/in‐situ‐grafted carbon black composite

The study on the dynamic viscoelastic properties of grafted carbon black (g‐CB) filled low‐density polyethylene (LDPE) was carried out. Because of formation of CB networking, the characteristic modulus plateau and loss tangent arc appears. Addition of grafting monomer like butyl acrylate (BA) and acroleic acid (AA) enhances the interaction between particles and matrix due to accelerated formation of micronetworking in the composites induced by forming branch chains of AA and BA with multiunit. The decrease of the temperature corresponding to α_c mechanical relaxation together with AA (BA) addition given by the position of loss tangent (tan δ) peak for LDPE is owed to the formation of long‐chain polymer grafted between CB and the matrix, which facilitates the slip of the lamella of LDPE. The influence of maleic anhydride (MA) on enhancing interaction between LDPE and CB is not so pronounced, as compared with AA and BA because of no formation of long chain between CB particle and polymer matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4127–4132, 2006     

Rheology of poly(propylene)/clay nanocomposites

The linear and nonlinear shear rheological behaviors of poly(propylene) (PP)/clay (organophilic‐montmorillonite) nanocomposites (PP/org‐MMT) were investigated by an ARES rheometer. The materials were prepared by melt intercalation with maleic anhydride functionalized PP as a compatibilizer. The storage moduli (G′), loss moduli (G″), and dynamic viscosities of polymer/clay nanocomposites (PPCNs) increase monotonically with org‐MMT content. The presence of org‐MMT leads to pseudo‐solid‐like behaviors and slower relaxation behaviors of PPCN melts. For all samples, the dependence of G′ and G″ on ω shows nonterminal behaviors. At lower frequency, the steady shear viscosities of PPCNs increase with org‐MMT content. However, the PPCN melts show a greater shear thinning tendency than pure PP melt because of the preferential orientation of the MMT layers. Therefore, PPCNs have higher moduli but better processibility compared with pure PP.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2427–2434,2004     

Molecular motions of non-crystalline poly(aryl ether-ether-ketone) PEEK and influence of elecron beam irradiation

The dynamic mechanical relaxation of non-crystalline poly(aryl ether-ether-ketone) PEEK and the one irradiated with electron beam were studied. The three distinct γ, β, α′ relaxation maxima were observed in unirradiated PEEK from low to high temperature. It was revealed from the study on the irradiation effects that three different molecular processes are overlapped in γ relaxation peak, i.e., molecular motion of water bound to main chain (peak temperature; at ?100°C), local motion of main chain (at ?80°C), and local mode of the aligned and/or oriented moiety (at ?40°C). The β relaxation connected with the glass transition occurred at 150°C and it shifted to higher temperature by irradiation. The α′ relaxation which can be attributed to rearrangement of molecular chain due to crystallization was observed in unirradiated PEEK ～ 180°C and its magnitude decreased with the increase in irradiation dose. This effect indicates the formation of structures inhibiting crystallization such as crosslinking and/or short branching during irradiation. A new relaxation, β′, appeared in the temperature range of 40° to 100°C by irradiation and its magnitude increased with dose. This relaxation was attributed to rearrangement of molecular chain from loosened packing around chain ends, which were introduced into the non-crystalline region by chain scission under irradiation, to more rigid molecular packing, From these observations, we proposed that deterioration in mechanical properties of non-crystalline PEEK by high energy electron beam was brought about not only by chain scission but structural changes such as crosslinking and/or branching in the main chain.