Low‐voltage and high‐transmittance blue‐phase liquid‐crystal device with slanted electrodes

Abstract— A low‐voltage (～10 V_rms) and high‐transmittance (～90%) polymer‐stabilized blue‐phase liquid‐crystal (BPLC) device with a slanted‐electrodes structure is proposed. Unlike the vertical‐field‐switching (VFS) mode in which oblique incident light and a vertical field are employed, the proposed device utilizes normal incident light and an oblique field. The slanted electrodes generate a strong and uniform oblique electric field, which contributes in obtaining low voltage and high transmittance. Moreover, no couple films or prism sheets are needed, which helps to enhance the optical efficiency and simplify of the device structure. This device has great potential application for emerging BPLC displays and photonic devices.     

以1,3-二(4-邻羟基苯亚胺次甲基)苯氧基丙烷为载体的铁离子(Ⅲ)电极的研究

以1,3-二(4-邻羟基苯亚胺次甲基)苯氧基丙烷为中性载体制备了PVC膜Fe3+离子选择性电极。该电极对Fe3+呈现出良好的选择性和近Nernst电位响应性能。电极斜率为21mV/dec,线性范围为3.0×10-5～1.0×10-1mol/L,检出限为1.0×10-5mol/L。采用交流阻抗技术研究了电极的响应机理,并将电极作为指示电极初步用于EDTA的电位滴定。     

基于2,4-二羟基苯甲酸铜(Ⅱ)为载体的硫氰酸根电极的电位响应

制备了基于一种简单的金属铜配合物2,4-二羟基苯甲酸铜(Ⅱ)(Cu(Ⅱ)DHBA)为载体的PVC膜硫氰酸根离子(SCN-)选择性电极。该电极在1.0×10-1～1.0×10-6mol/LSCN-浓度范围内呈现斜率为-59.5mV/dec的近Nernst电位响应,检测下限为9.1×10-7mol/L。利用紫外可见光谱及交流阻抗技术初步探讨了电极对SCN-呈现的选择性电位响应机理。该电极作为直接电位分析法的指示电极,成功运用于实验室废水中硫氰酸盐含量的测定。     

Electrochemical investigation of the iron-containing and no iron-containing AB5-type negative electrodes

The electrochemical behaviour of LaNi_3.55Mn_0.4Al_0.3Co_0.75−xFe_x (x = 0, 0.15, 0.55, 0.75) intermetallic compounds has been studied and presented [C. Khaldi, H. Mathlouthi, J. Lamloumi, A. Percheron-Guégan, Int. J. Hydrogen Energy 29 (2004) 307–311; C. Khaldi, H. Mathlouthi, J. Lamloumi, A. Percheron-Guégan, J. Alloys Compd. 360 (2003) 266–271; C. Khaldi, H. Mathlouthi, J. Lamloumi, A. Percheron-Guégan, J. Alloys Compd. 384 (2004) 249–253]. It has been deduced that the LaNi_3.55Mn_0.4Al_0.3Co_0.4Fe_0.35 compound has interesting electrochemical properties. In this paper we present the electrochemical study of LaNi_3.55Mn_0.4Al_0.3Co_0.4Fe_0.35 compound properties compared with the parent LaNi_3.55Mn_0.4Al_0.3Co_0.75 compound. Several techniques, such as, the chronopotentiometry, the constant potential discharge (CPD), the cyclic voltammetry (CV) and the linear polarization (LP) were applied to characterize these electrochemical properties. The electrochemical discharge capacity of the LaNi_3.55Mn_0.4Al_0.3Co_0.75 alloy increases to reach 294 mAh g⁻¹ after few cycles only (five cycles). However, the activation of the LaNi_3.55Mn_0.4Al_0.3Co_0.4Fe_0.35 alloy takes more than 20 cycles to be achieved and the obtained maximum discharge capacity is 194 mAh g⁻¹. The hydrogen diffusion coefficient D_H was determined by constant potential discharge and cyclic voltammetry techniques. The obtained values of the LaNi_3.55Mn_0.4Al_0.3Co_0.75 and LaNi_3.55Mn_0.4Al_0.3Co_0.4Fe_0.35 compounds are 6.29 × 10⁻¹¹ and 7.62 × 10⁻¹¹, and 2 × 10⁻⁸ and 7.5 × 10⁻⁸ cm² s⁻¹ by CPD and CV techniques, respectively. The exchange current density values, determined by a linear polarization technique, are 44 and 27 mA g⁻¹, respectively, for LaNi_3.55Mn_0.4Al_0.3Co_0.75 and LaNi_3.55Mn_0.4Al_0.3Co_0.4Fe_0.35 alloys.     

小波变换在伺服焊枪电极位移曲线分析中的应用

电极位移曲线能够反映出点焊规范参数波动，是一个理想的监控参数。采用离散Daubechies4阶小波对电极位移曲线进行滤波处理，成功地将测量曲线分为电极位移趋势曲线、波动曲线。这两种曲线分别反映了点焊质量的整体质量优劣、过程一致性这两方面特征，提高了位移曲线表征焊接过程的能力，为伺服焊枪的点焊质量控制提供了准确、优良的数据基础。     

二元稀土系AB5型贮氢电极合金的放电容量与晶胞体积和4f电子浓度的关系

制备了6个系列通式为AαA‘1-αB5的RE(NiCoMnTi)5贮氢电极合金(其中，AαA‘1-α为La，Ce，Pr，Nd4个元素中任意2个的组合)，测定了它们在100次循环中的最大放电容量Cmax及部分合金的晶胞体积Vcell．结果表明：Cmax主要由Vcell决定，Cmax先随Vcell的增大而增加，在Vcell≈85．66x10^-^3。nm^3时达到一极大值，然后又随Vcell的增大而减小；同时，Cmax还与4f电子浓度ne4f／naRE有关，A侧具有相同4f电子浓度的合金其Cmax随4f电子浓度的变化趋势相似．     

电渗模型电阻测量技术

本文对电渗模型中电阻测量方法进行了改良,提出串联法代替当前的电势测针法和夹具法,并提出了适用于测量EKG电极电阻的走线法。串联不同长度的电渗土体测量电极与土体间的接触电阻消除了电势测针法中测针与电极之间一段土体电阻值的误差影响,同时避免了电势测针插入土壤对土壤电流分布的影响;串联不同长度的电渗电极测量电极电阻率时消除了夹具法测量时夹具和电极之间接触电阻的误差影响。经试验结果表明：电势测针法所得的接触电阻与串联法得到的接触电阻比值大多在1.3~1.4之间,验证了电势测针法将测针与电极间的一段土体值计入了接触电阻造成所测得的接触电阻偏大,该值的大小取决于该段土体电阻值;串联法对于当前应用广泛的EKG电极并不适用,提出了走线法来测量EKG电极电阻率消除电极板内因嵌入铜制导线电流分布不均的影响,走线法测量结果基本不受电极长度的影响,具有良好的可靠性和稳定性,走线法测量便捷,方便应用于EKG电极生产工艺中,有比较广阔的应用前景;走线法测量EKG电极所得的电阻率与夹具法得到电阻率的比值大多在8%~10%之间,该比值主要与夹具电极板间的接触电阻相关,夹具和电极板之间的接触电阻仅取决于夹具和电极板,故可利用该比值对先前使用夹具法的测量结果进行修正,在许多室内试验和工程中均用到了EKG电极,考虑EKG电极电阻率对整个试验和工程的能耗影响时可参考电阻率比值0.08~0.1进行修正。     

电火花成形机主轴电极头的流固耦合分析

电火花成形机主轴电极头在回退、直至完全离开工作液的过程中,会受到工作液对其表面产生的阻力作用.研究主轴电极头所受的液体阻力,为主轴支承件的有限元分析和优化设计提供详实可靠的理论依据.     

Application of electrode materials and catalysts in electrocatalytic treatment of dye wastewater

The dye industry produces a large amount of hazardous wastewater every day worldwide, which brings potential threaten to the global environment. As an excellent method for removal of water chroma and chemical oxygen demand, electrocatalytic methods are currently widely used in the treatment of dye wastewater. The selection and preparation of electrode materials and electrocatalysts play an important role on the electrocatalytic treatment. The aim of this paper is to introduce the most excellent high-efficiency electrode materials and electrocatalysts in the field of dye wastewater treatment. Many electrode materials such as metal electrode materials, boron-doped diamond anode materials and three-dimensional electrode are introduced in detail. Besides, the mechanism of electrocatalytic oxidation is summarized. The composite treatment of active electrode and electrocatalyst are extensively examined. Finally, the progress of photo-assisted electrocatalytic methods of dye wastewater and the catalysts are described.     

多级结构MoS2/C复合材料的储锂性能

利用二硫化钼和葡萄糖为原料,采用一锅乙醇/水复合溶剂热-后热处理法制备了绣球花状结构MoS₂/C复合材料。考查了乙醇/水复合溶剂的合理组成和MoS₂/C复合材料中碳的合理含量,分别采用SEM和TEM表征了MoS₂/C材料的形貌结构,通过TGA测试和计算了材料中的碳含量。采用循环伏安、恒流充放电和交流阻抗等测试了MoS₂/C复合电极的电化学性能。结果表明,MoS₂/C复合材料拥有多级花球状结构,缓解了MoS₂的团聚,使电极材料的利用率和电化学稳定性显著提高。当V（乙醇）：V（水）为1：2,碳含量为50%时,MoS₂/C复合电极在200 mA·g^-1的电流密度下,充放电循环100次后,可逆容量达到762 mA·h·g^-1。