全文获取类型
收费全文 | 20988篇 |
免费 | 2425篇 |
国内免费 | 1025篇 |
专业分类
电工技术 | 1652篇 |
综合类 | 2216篇 |
化学工业 | 3866篇 |
金属工艺 | 818篇 |
机械仪表 | 1191篇 |
建筑科学 | 4986篇 |
矿业工程 | 1212篇 |
能源动力 | 610篇 |
轻工业 | 997篇 |
水利工程 | 419篇 |
石油天然气 | 849篇 |
武器工业 | 149篇 |
无线电 | 1588篇 |
一般工业技术 | 1563篇 |
冶金工业 | 623篇 |
原子能技术 | 249篇 |
自动化技术 | 1450篇 |
出版年
2024年 | 70篇 |
2023年 | 295篇 |
2022年 | 524篇 |
2021年 | 676篇 |
2020年 | 682篇 |
2019年 | 601篇 |
2018年 | 511篇 |
2017年 | 723篇 |
2016年 | 782篇 |
2015年 | 845篇 |
2014年 | 1373篇 |
2013年 | 1308篇 |
2012年 | 1634篇 |
2011年 | 1711篇 |
2010年 | 1224篇 |
2009年 | 1242篇 |
2008年 | 1178篇 |
2007年 | 1393篇 |
2006年 | 1232篇 |
2005年 | 1012篇 |
2004年 | 862篇 |
2003年 | 734篇 |
2002年 | 660篇 |
2001年 | 574篇 |
2000年 | 482篇 |
1999年 | 380篇 |
1998年 | 306篇 |
1997年 | 342篇 |
1996年 | 221篇 |
1995年 | 177篇 |
1994年 | 135篇 |
1993年 | 101篇 |
1992年 | 97篇 |
1991年 | 70篇 |
1990年 | 57篇 |
1989年 | 65篇 |
1988年 | 44篇 |
1987年 | 33篇 |
1986年 | 19篇 |
1985年 | 7篇 |
1984年 | 7篇 |
1983年 | 3篇 |
1982年 | 4篇 |
1981年 | 2篇 |
1980年 | 17篇 |
1979年 | 9篇 |
1974年 | 2篇 |
1963年 | 1篇 |
1959年 | 1篇 |
1951年 | 5篇 |
排序方式: 共有10000条查询结果,搜索用时 15 毫秒
61.
再论异重流和均质流动的一些相似关系 总被引:1,自引:1,他引:0
在对上层静止下层流动的异重流和均质明渠流之间相似关系研究的基础上,本文将这一成果推广,给出了上层流动下层静止的异重流和均质明渠流之间的一些相似关系,并将结果应用于二维重叠式排取水口的水深计算,结果与前人的实验一致。考虑到实际的重叠式排取水口都是三维的,所以本文利用前人的实验结果,进一步给出了三维重叠式排取水口高度及水深的计算方法,所得结果揭示了排水口温差水跃的形成机理和形成条件。 相似文献
62.
63.
������Һ������� 总被引:4,自引:0,他引:4
油管柱作为油气生产中的重要工具,它的使用寿命一直是工程技术人员关注的焦点。文章从动力学中固液耦合振动的角度出发,研究了油管柱内流体不稳定流动引起的油管柱振动问题。考虑液动压力对油管柱纵向振动的影响,建立了油管柱纵向振动微分方程,并给出了这种情况下油管柱纵向振动的频率方程。通过大天池构造上一口高压气井的实例计算分析,指出井内流体不稳定流动时,油管柱会产生相当高的附加动载。这个动载是造成油管柱在生产过程中发生疲劳破坏的主要原因之一,在今后的油管柱设计中应考虑这一动载的影响 相似文献
64.
报导一种全新冷却方式的双椭圆泵浦腔,具有较高的泵浦效率和光学均匀性。1.06μm调Q脉冲输出能量总转换效率η>0.75% 相似文献
65.
在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。 相似文献
66.
An original procedure has been established for estimating the overall volumetric mass transfer coefficient using the oxygen concentration curves resulting from the usual gassing-in and gassing-out method. This procedure was applied to experimental data obtained in a small scale bubble column using both tap water and a coalescence-inhibiting liquid mixture that represents the coalescence behavior of biological media. It is based on the analysis of the characteristics times of the system, including those of the hydrodynamics of the two phases, the sensor dynamics and the system inertia when the gas composition is modified. A numerical procedure was developed to estimate the characteristic time of the system inertia ti, using the assumption that this inertia is nearly independent of superficial gas velocity UG. The calculations confirmed that the optimized ti value was nearly independent of UG and of the coalescence behavior of the liquid phase. Additionally, the resulting KLaL values for tap water were closer to the correlation of Shah et al. [1982. Design parameters estimations for bubble column reactors. A.I.Ch.E. Journal 28, 353-379] than those of other conventional models. Finally, the original procedure was also reported to reduce significantly the square sum deviation between the predicted and the measured oxygen response curves. 相似文献
67.
基于变轴力和定轴力试验对比的钢筋混凝土柱恢复力滞回特性研究 总被引:6,自引:1,他引:5
在讨论了框架柱在地震作用下轴力变化规律的基础上,通过由变轴力柱和定轴力柱的低周交变加载试验获得的恢复力滞回曲线对比,给出了用各个“轴力变化半周”的“等效滞回轴力”修正恢复力骨架曲线,和用“等效累积滞回轴力”随时间步长调整累积强度退化系数从而修正恢复力滞回曲线的再加载刚度的建议。该建议能更有效、更方便地反映轴力变化的整个历程对变轴力柱恢复特征的影响,有利于提高钢筋混凝土杆系结构非弹性地震反应分析的有效性。 相似文献
68.
纯铜双层辉光离子渗钛组织形成机理及性能分析 总被引:6,自引:0,他引:6
采用双层辉光离子渗金属技术对纯铜进行了渗钛处理。用配有能谱仪(EDS)的扫描电子显微镜(SEM)、X射线衍射仪和透射电子显微镜对合金层的显微组织形貌、钛含量分布、相组成及相结构类型进行了观察与测定,对合金层的形成机理进行了探讨,并对其性能进行了对比测定。结果表明:渗钛层由合金层和扩散层组成,合金层主要由TiCu (Cu)固溶体 TiCu4构成,TiCu4为Dla型有序相,TiCu为B2型有序相,扩散层为(Cu)固溶体。渗钛处理后纯铜的表面得到显著强化。 相似文献
69.
本文为了克服精馏塔静态仿真不易收敛和初值难以给定等难题,巧妙地利用隐含数值积分方法的特点,将稳态与动态数学模型耦合起来,用以求解高难度的非理想精馏塔静态仿真问题。所得静动态混俣模型大大提高了精馏塔静态仿真的鲁棒性,对于高度非理想精馏塔的仿真尤为有效。通过对某丙烯腈萃取精馏塔的静态仿真,充分证明了这种混合模型化方法的可行性。 相似文献
70.
Claudio Arbib Fabrizio Marinelli 《International Journal of Flexible Manufacturing Systems》2003,15(4):333-354
A cook has to prepare n cakes using an oven with two racks. According to the recipe, the i-th cake has to be baked for exactly a
i minutes. Cakes to be cooked are taken from a table and carried to the oven, and once cooked are carried back to the table by means of a trolley that can carry two cakes at a time. What is the minimum number q
* of round trips required of the cook? This problem has application to the operation scheduling of transportation systems and to material cutting. A different problem arises according to whether the cook accepts or not to stay near the oven for awhile with the trolley. If the trolley cannot be idle at the oven, an optimum schedule with no oven idle-time always exists: consequently, the trolley schedule is trivial, and the problem is transformed into a set packing. For this case, we propose and test a heuristic method which generates all of the promising columns of the set packing, and solves the resulting problem by branch-and-bound. Instead, if the trolley can be idle at the oven for a limited amount of time, a problem arises to find an optimal schedule of the trolley: in this case we show how to use a scaling technique in order to obtain a very good feasible solution by the method above. 相似文献