便携式无线通信中的陶瓷技术

重点讨论了现代无线通信中关键元器件之一滤波器的发展进程,中、高频及微波滤波器的主要类型及性能特点。低损耗、高介电常数陶瓷在RF和IF滤波器中的应用,能够实现无线设备的微型化。对制备滤波器的介质陶瓷材料的要求是:在所使用的波段内,相对介电常数r要大,可缩小介质元件的尺寸;品质因数Q要高,可获得良好的滤波特性及通讯质量;谐振频率的温度系数f接近于零或可调节,以达到整机电子回路的要求。     

ZST微波陶瓷在介质振荡器上的应用研究

用传统固相法制备ZST(氧化锆-氧化锡-氧化钛)系微波陶瓷,研究了ZST系微波陶瓷的组成对介电性能的影响。通过X-射线衍射(XRD)和HP8714ET网络分析仪对其晶体结构和微波介电性能进行研究,实验结果表明:少量掺Bi2O3的ZST系陶瓷材料可把烧结温度降低至1 260℃,微波介电性能较好;掺入量大于2%(质量分数)时,ZST系微波陶瓷在晶界偏析形成了Bi2Ti2O7新相,微波性能下降。用微波介电性能较好的ZST系陶瓷制成的介质振荡器进行测试,其电性能满足设计要求。     

微波感应式电力线防盗在线监测系统

研制了一种微波感应式配电线路防盗在线监测系统，简述了其系统构成、技术特点和应用效果。整个系统由监测分机、监控中心、巡检人员组成，借助该系统进行了一系列实验。结果表明，当有大型移动物体靠近或攀登杆塔时，安装在杆塔上10 m左右的微波感应监测分机感应到移动物体信号，一方面进行语音警示，另一方面通过短信服务及时向监控中心发送短信，监控中心及时通知巡检人员，赶到事故现场，以最大限度地保证输电线路的安全。     

广义Foster定理

利用Ｍａｘｗｅｌｌ方程组导出了适用于有耗网络的广义Ｆｏｓｔｅｒ定理，得到了一些有关电抗斜率以及Ｑ值的有用公式及结论。     

Microwave surface resistance of epitaxial YBa2Cu3O7 thin films at 18.7 GHz measured by a dielectric resonator technique

We used a dielectric resonator technique for highly sensitive measurements of the temperature dependence of the microwave surface resistanceR _s of 1×1 cm² superconducting films at 18.7 GHz. It consists of a sapphire disc positioned on the film under investigation within a copper cavity which is acting as a radiation shield. In the TE₀₁ oscillation mode the highly reproducible quality factor of about 10⁵ results in a sensitivity of ±50 forR _s measurements. The temperature dependence ofR _s can be measured up to values as high as 1 . We have investigated several YBa₂Cu₃O₇ thin films prepared by high oxygen pressure d.c. sputtering on LaAlO₃ and NdGaO₃. Our best films exhibit a pronounced nonlinear behavior of the d.c. resistivity(T) with(300K)/(100K) values of about 3.7. Those films show, besides the initial fall-off just belowT _c , a further strong decrease ofR _s at low temperatures. This was observed both at 18.7 GHz and 87 GHz, as measured by a conventional cavity end plate replacement technique. ForTT_c/2 these films exhibit an exp (–T _c/T) dependence ofR _s with-values around 0.4. These observations may be explained by a superconducting energy gap with 2/kT _c0.8 for charge carriers localized in the CuO chains for YBa₂Cu₃O₇.     

Facile Deposition of Silver Nanoparticles on Photonic Cellulose Nanocrystals Films: A Study on Solvent Stability and Post Antibacterial Activity

Cellulose nanocrystals (CNCs) incorporated with silver nanoparticles (AgNPs) photonic films have drawn considerable attention due to their plasmonic chiroptical activity. However, the exploitation of some fundamental properties for practical use such as the affinity analysis of metal nanoparticles attached to the surface of photonic films according to the solvent compatibility and antibacterial activity under physical conditions has yet not been studied. Hence, a facile process of in situ deposition of AgNPs into the chiral structure of CNC films is proposed. CNC photonic films, cross-linked by glutaraldehyde are prepared. This interaction generated the solvents-stable photonic film with a considerable amount of unreacted aldehyde functional groups that facilitates the reduction of Ag salt to AgNPs. The formed AgNPs in the photonic films show excellent stability over immersion in various polar and non-polar solvents. The post-solvent treated photonic films display excellent contact-based antibacterial behavior against gram-negative Escherichia coli.     

Global insight into microwave stoneware firing: Macro and microstructural changes

Industrial competition and environmental concerns lead to the exploration of alternative and energy-efficient technologies for ceramic materials processing. The main objective of this work was to present microwave heating as a viable option for stoneware processing. Stoneware functional properties are presented and discussed, with emphasis on impact strength, water absorption, porosity, and color. Microstructure analyses show that microwave- and gas-fired samples have higher densifications than electrically fired samples. A relevant finding for processing conditions is that microwave firing requires temperatures approximately 100°C lower than those required by conventional firing. Microwave-fired samples’ rupture energies are approximately twice (0.57 ± 0.06 (J)) those of the reference samples (0.26 ± 0.03 (J)), and their water absorptions are approximately one-half (1.5% at 1170°C and 0.8% at 1190°C) of those of the reference samples (2.0%), whereas the water absorption of electrically fired samples at 1180°C has been estimated to be 7.5%. Color analysis also evidences a shift to lower microwave firing temperatures, what is attributed to the enhanced transformations promoted by microwave heating when comparing with the transformations promoted by conventional (gas or electric) heating.     

氟硅酸钾滴定法测定粗制氟化钠中二氧化硅

采用硝酸-氢氟酸混合酸为消解溶剂,通过微波消解技术对粗制氟化钠进行快速消解,并用氟硅酸钾滴定法测定其二氧化硅含量。选择饱和氯化钾溶液替代固体氯化钾作为沉淀剂,考察了消解酸体系、饱和氯化钾溶液用量、沉淀温度、沉淀放置时间、共存元素干扰及指示剂选择等条件对测定结果的影响并进行优化。确定了最优测试条件：以8 mL硝酸+2 mL氢氟酸为消解溶剂,以8 mL饱和氯化钾溶液为沉淀剂,控制沉淀温度为20~25 ℃、沉淀放置时间为15 min,选择50 g/L氯化钾-50%乙醇溶液洗涤沉淀,采用溴麝香草酚蓝-酚红指示剂。该方法应用于回收粗制氟化钠中二氧化硅含量的测定可大幅度缩短分解试样的时间,有效降低检测成本,回收率为99.15%~100.63%,相对标准偏差（RSD,n=8）小于1%,与传统高温碱熔法测定结果相符,方法的准确度和精密度较好。     

Preparation of alumina-doped yttria-stabilized zirconia nanopowders by microwave-assisted peroxyl-complex coprecipitation

Alumina-doped yttria-stabilized zirconia （ADYSZ） nanopowders were prepared by microwave-assisted peroxyl-complex coprecipitation （MAPCC） using ZrOCl2-8H2O, Y2O3 and AICly6H2O as starting materials, NH2-H2O as precipitant and H2O2 as complexant. The effects of adding H2O2 and microwave drying on the preparation and properties of ADYSZ were investigated. The precursors and nanopowders were studied by EDX, XRD, SEM and TEM techniques. The results show that the uniformity of component distribution within ADYSZ nanopowders is improved by adding appropriate dosage of H2O2. Complexing reaction between H2O2 and Zr^4＋ ion restrains the hydrolyzation and precipitation of Zr^4＋ ion. With the addition of H2O2, Al^3＋, y^3＋ and Zr^4＋ ions can be precipitated synchronously in a relatively narrow range of pH value. H2O2 also improves the filterability of the wet precipitate. The highly hydrophilic precipitates can be quickly and effectively separated from aqueous solution. During microwave drying process, the moisture of wet precursors is selectively heated. Quick expansion of steam vapor within the wet colloidal particles causes the aggregations burst into numerous tiny lumps. Compared with oven drying, microwave drying can not only shorten drying time but also reduce aggregation intensity of the resultant ADYSZ nanopowders.