A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

Dielectric,ferroelectric, and energy storage properties in dysprosium doped sodium bismuth titanate ceramics

In this work, Na_0.5(Bi_1-xDy_x)_0.5TiO₃ (0?≤?x?≤?15%) ceramics were prepared via solid state reaction method and were characterized. A stable and pure perovskite phase was revealed by X-ray diffraction analysis for all compositions and a symmetry change from rhombohedral to orthorhombic phase was detected beyond 10% of Dy substitution. The incorporation of Dy³⁺ into Sodium Bismuth Titanate (Na_0.5Bi_0.5TiO₃) matrix allows a substantial decrease of the coercive field, an increase in the resistivity, and leads to a high stability of the dielectric permittivity (??/?_(150?°C) ≤?±?15%) over a wide temperature range. Furthermore, this system was found to exhibit improved energy storage properties at high temperatures with a maximum energy density of 1.2?J/cm³ obtained for 2%Dy composition at 200?°C. The obtained results are very promising for energy storage capacitors operating at high temperatures.     

Preparation and temperature-resistance characteristics of novel dense SiAlCN ceramics

The compact green bodies, prepared via a novel solid-liquid mixing method of precursors, were successfully pyrolyzed to obtain the dense bulk SiAlCN ceramics at 1000 °C. It can be seen from their SEM that they have uniform and dense microstructure, indicating that this method can be used to prepare bulk ceramics. In order to verify that they can be used as sensor heads, their temperature-resistance characteristics and repeatability were tested. The results show that the conductive mechanism belongs to Arrhenius's Tailed-State and Extended-State in the temperature range of 500–650 °C and 650–930 °C, respectively. And it shows that SiAlCN ceramics can be used as the sensor heads for high-temperature sensors.     

Grain size dependence of hardness in nanocrystalline silicon carbide

The response of nanocrystalline silicon carbide (nc-SiC) to nanoindentation is investigated using molecular dynamics (MD) simulation. It is found that the hardness of the nc-SiC decreases with decreasing grain size, showing an inverse Hall-Petch relationship. The behavior is primarily attributed to the reduced number of intact covalent bonds with grain refinement. Dislocation nucleation and growth in nc-SiC are strongly suppressed by the grain boundaries (GBs). In addition to the dislocation region in the grains, the indentation-induced amorphization of nanograins proceeds preferentially from the GBs, leading to grain shrinkage until the grains are fully amorphized. The results provide an improved understanding of the mechanical properties in nc-SiC and other nanostructured covalent materials.     

Coexistence of three ferroelectric phases and enhanced piezoelectric properties in BaTiO3–CaHfO3 lead-free ceramics

Perovskite ferroelectrics possess the fascinating piezoelectric properties near a morphotropic phase boundary, attributing to a low energy barrier that the results in structural instability and easy polarization rotation. In this work, a new lead-free system of (1-x)BaTiO₃-xCaHfO₃ was designed, and characterized by a coexistence of ferroelectric rhombohedral-orthorhombic-tetragonal (R-O-T) phases. With the increase amount of CaHfO₃ (x), a stable coexistence region of three ferroelectric phases (R-O-T) exists at 0.06 ≤ x ≤ 0.08. Both large piezoelectric coefficient (d₃₃～400 pC/N), inverse piezoelectric coefficient (d₃₃^*～547 pm/V) and planar electromechanical coupling factor (k_p～58.2%) can be achieved for the composition with x = 0.08 near the coexistence of three ferroelectric phases. Our results show that the materials with the composition located at a region where the three ferroelectric R-O-T phases coexist would have the lowest energy barrier and thus greatly promote the polarization rotation, resulting in a strong piezoelectric response.     

攀西钒钛磁铁矿尾矿制备储水泡沫陶瓷的研究

以攀西钒钛磁铁尾矿和废玻璃为主要原料通过高温烧结法制备储水泡沫陶瓷，研究原料配比和发泡剂（SiC）添加量对材料性能的影响。结果表明:随着钒钛磁铁矿尾矿含量的增加，材料的体积密度及抗压强度逐渐增大，平均气孔孔径逐渐减小；当尾矿添加量为50 wt%，材料的体积吸水率出现极值。当SiC添加量为0.3 wt%，材料内部气孔分布均匀，平均孔径约为2.93 mm。最终以50.0 wt%的钒钛磁铁矿尾矿和50.0 wt%的废玻璃为原料，外加3.0 wt%的石英，0.3 wt%的SiC，3.0 wt%的Na3PO4，在1040℃下制得性能最优的储水泡沫陶瓷，材料的体积密度为0.26 g/cm-3、体积吸水率为56.5%和抗压强度为0.68 MPa。采用SEM、XRD等检测手段研究材料的微观形貌及物相组成，结果表明储水泡沫陶瓷内部由三维立体结构组成，有利于储存水分；材料主要物相包括硅灰石、长石、透辉石和钛铁矿。      

Enhanced transduction coefficient in piezoelectric PZT ceramics by mixing powders calcined at different temperatures

Large transduction coefficient ($d_{33}\times g_{33}$) is difficult to obtain in piezoelectric ceramics because these two parameters show opposite trends with compositional modifications. Herein, the Pb(Zr_0.53Ti_0.47)O₃ ceramic powders were calcinated under different temperatures (A:830 °C, B:860 °C, and C:890 °C), and then mixed together according to different weight ratios (1A:1B:1C, 1A:2B:1C, 1A:2B:3C and 3A:2B:1C) for ceramics preparation. Both d₃₃ and g₃₃ are improved successfully, and the transduction coefficient with the weight ratio of 1A:2B:3C reaches up to 17,500 × 10⁻¹⁵ m²/N, which is 60 % higher than that with the powders calcinated under 830 °C, and at least twice those of commercial PZT-4, PZT-5A and PZT-8 ceramics. The improved transduction coefficient is owing to the enhanced piezoelectric constant and spontaneous polarization resulted from the increased grain size, relative density and the fraction of tetragonal phase. These results indicate that this is a simple but effective way to tailor the transduction coefficient in piezoelectric ceramics.     

Enhanced piezoelectric strain of BiFeO3–Ba(Zr0.02Ti0.98)O3 lead-free ceramics near the phase boundary

The xBiFeO₃-(1-x)Ba(Zr_0.02Ti_0.98)O₃ + 1.0 mol% MnO₂ (xBF-BZT) lead-free piezoelectric ceramics were prepared by conventional solid-state reaction method. The structure, dielectric, and piezoelectric properties were studied. X-ray diffraction (XRD) analysis showed that xBF-BZT ceramics exhibited pure perovskite structure with the coexistence of tetragonal and rhombohedral phases (0.66 ≤ x ≤ 0.74). The Curie temperature T_c, the dielectric constant ε_r (1 kHz), dielectric loss tanδ (1 kHz), piezoelectric constant d₃₃, coercive field E_c (80 kV/cm), and remnant polarization P_r (80 kV/cm) of 0.7BF-0.3BZT-Mn ceramics were 491°C, 633, 0.044, 165 pC/N, 35.6 kV/cm, and 22.6 μC/cm², respectively. The unipolar strain of 0.7BF-0.3BZT reached up to 0.20% under the electric field of 60 kV/cm, which is larger than that (0.15%) of BiFeO₃–BaTiO₃ ceramics. These results indicated that the xBF-BZT ceramics were promising candidates for high-temperature piezoelectric materials.     

Erbium doped Bi2O3-B2O3 glass-ceramics containing Bi3B5O12 and CaF2 nanocrystallites for 1.53 μm fiber lasers

Trivalent erbium ions doped Bi₂O₃-B₂O₃ transparent glass ceramics containing CaF₂ were prepared and characterized through X -ray diffraction, scanning electron microscopy, Fourier transform infrared absorption, optical absorption, and near infrared emission for 1.53 μm fiber lasers. The glass ceramics obtained by applying thermal treatment at 575 °C for 5 h and 575 °C for 10 h contain Bi₃B₅O₁₂ and CaF₂ crystallites. The Judd-Ofelt theory was applied to evaluate various spectroscopic and laser characteristic properties. The NIR emission corresponding to the ⁴I_13/2 → ⁴I_15/2 (∼1.53 μm) transition was studied by exciting the samples at 514.5 nm laser radiation. The stimulated emission cross-sections of ∼1.53 μm luminescence were also obtained applying the Mc Cumber theory. The experimental results confirm that the transparent glass ceramic obtained at a thermal treatment of 575 °C for 10 h is more suitable to design fiber lasers for diverse applications in the fields of industry, medicine and scientific research.     

Al2O3陶瓷激光铣削试验研究

采用Nd∶YAG脉冲激光器对Al2 O3陶瓷进行铣削加工试验。系统研究了工艺参数对铣削量和铣削面质量的影响规律 ,并利用优化的铣削工艺对Al2 O3陶瓷进行多种形状的铣削加工。