Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Effect of in-situ formation of columnar mullite and pore structure refinement on high temperature properties of corundum casatbles

The effects of in-situ synthesis columnar mullite and pore structure on the hot modulus of rupture (HMOR), thermal shock resistance and corrosion resistance of corundum castables have been investigated in this paper. When 2% nano silica was added, the pore diameters of castables could be decreased to 15 nm (at 110 °C), 1 μm (1100 °C) and 6 μm (1500 °C), respectively. The corresponding reducing magnitude of pore size is 98.5%, 83.3% and 33.3%. The HMOR of castables fired at 1500 °C increased by 110% to 3.64 MPa. Furthermore, after three thermal shock cycles, the residual strength ratio of castables increased from 5.2% to 15.3%. A large amount of cross-distributed columnar mullite was formed between nano silica and α-Al₂O₃ by the two-dimensional nucleation mechanism, which remarkably enhanced the high temperature properties. The penetration index reduced from 30.86% to 19.88%, suggesting that smaller pore size and higher viscosity had a great influence to the penetration process.     

钢铁行业烟气多污染物协同控制技术应用实践

本研究分析了钢铁企业焦化和烧结两个重点工序中烟气污染物排放现状和钢铁行业当前的环保政策。对焦化及烧结烟气污染物的排放特征进行了分析，并通过对比燃煤电厂烟气特点，提出可以综合电厂烟气治理模式和自身特点改进的技术路线。结合某大型国有钢铁企业的脱硫脱硝装备对其环保现状进行了分析。针对焦化和烧结工序的典型污染物硫、硝、尘现有的源头减排、过程控制及末端处理技术，分析其优缺点。进而提出了3条可实现烟气污染物超低排放的技术路线，即半干法脱硫耦合选择性催化还原脱硝、半干法/湿法耦合臭氧氧化脱硝、活性焦脱硫脱硝一体化技术，重点介绍了这些技术在某大型钢铁企业的应用实践及应用效果。并基于全过程耦合技术，分别在焦化和烧结工序中提出了多污染物协同去除技术及应用，即焦炉低氮燃烧技术耦合末端活性焦多污染物协同控制技术、烧结烟气循环技术耦合末端活性焦多污染物协同控制技术。最后结合几种技术路线的应用实践，对未来钢铁产业的烧结及焦化工序超低排放技术的选择提出合理化建议。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

温度对生物净化滤柱中氨氮、铁、锰去除效果的影响

温度是生物净化滤柱运行的一个重要参数，采用生物净化滤柱处理模拟含氨氮、铁、锰地下水，考察水温从约25℃降到约6℃过程中氨氮、铁、锰的去除效果。结果表明，出水氨氮、总铁、锰的浓度分别低于0.15mg/L、0.1mg/L、0.05mg/L，均低于国家标准。出水总铁、锰均未受到水温下降的影响，但是出水氨氮浓度逐渐从约0.02mg/L升高到约0.12mg/L。进一步分析发现，铁主要在滤层的0~0.4m段去除，去除效果没有受到水温变化的影响。氨氮、锰主要在滤层的0~0.8m段去除，其沿程浓度均随水温降低而明显升高。氨氮、锰的生物去除符合一级动力学反应，水温为24.6℃、15.3℃、6.7℃时，两者的动力学常数k分别为0.154min^-1、0.186min^-1，0.143min^-1、0.175min^-1，0.103min^-1、0.163min^-1；半反应时间t_1/2分别为4.51min、3.72min，4.83min、3.96min，6.72min、4.24min。随着试验水温的降低，氨氮、锰的去除效果明显受到影响。     

A Constitutive Equation of Thermoelasticity for Solid Materials

A new constitutive equation of thermoelasticity for crystals is presented based on the interatomic potential and solid mechanics at finite temperature. Using the new constitutive equation, the calculations for crystal copper and graphene are carried out under different loading paths at different temperatures. The calculated results are in good agreement with those of the previous thermoelasticity constitutive equation based on quantum mechanics, which clearly indicates that our new constitutive equation of thermoelasticity is correct. A lot of comparisons also show that the present theory is more concise and efficient than the previous thermal stress theory in the practical application.     

High-Tg porous polyimide films with low dielectric constant derived from spiro-(adamantane-2,9′(2′,7′-diamino)-fluorene)

Porous polyimide (PI) films with low dielectric constants and excellent thermal properties have been a pressing demand for the next generation of high-performance, miniature, and ultrathin microelectronic devices. A series of novel porous PI films containing fluorenyl-adamantane groups were prepared successfully via thermolysis of poly(ethylene glycol) (PEG) added in the PI matrix. The cross-sectional morphologies of porous PI films showed closed pores with diameters ranging from 135 to 158 nm, which were uniform and regular in shape without interconnectivity. These porous PI films exhibited excellent thermal properties with a glass-transition temperature at 376 °C whereas the 5% weight loss temperature in air excess of 405 °C due to enhanced rigidity afforded by fluorenyl-adamantane groups. Accompanied by thermolysis content of PEG increasing from 0 to 20 wt %, the density of porous PI films decreased, and the corresponding porosity grew significantly from 0 to 11.48%. Depending on porosity, the dielectric constant and dielectric loss of porous PI films significantly declined from 2.89 to 2.37 and from 0.050 to 0.021, respectively. These excellent properties benefit the as-prepared porous PI films for application as interlayer dielectrics, integrated circuit chips, or multichip modules in microelectronic fields. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47313.     

邢钢180 m2烧结机提高混合料温度的实践

介绍了邢钢180 m^2烧结机投产以来,在提高混合料温度方面所采取的主要措施.该厂通过提高生石灰质量、采用蒸汽预热混合料、在混合机中加热红泥浆等,改善了混合料的透气性,进而提高了烧结矿产、质量.     

高温高盐高含水油藏提高水驱采收率配套技术

针对江汉油区高温高盐高含水油藏的储层条件,应用国内外油藏精细描述、油藏工程最新理论与技术,提出了高含水油田合理钻加密井、完善注采井网、水平井挖潜、不稳定注水及高温高盐油藏采油工艺配套技术措施,形成了一套适应高温高盐高含水油藏提高水驱采收率的配套技术。