20%乙·苄可湿性粉剂的高效液相色谱分析

本文采用高效液相色谱法,以乙腈+水(60+40)作为流动相,使用C18柱,在同一条件下,同时成功地测定出20%乙·苄可湿性粉剂中的二元有效成份含量。该方法快速准确,乙草胺测定方法的相关系数为0.99986,平均回收率99.2%,苄黄隆测定方法的相关系数为0.99996,平均回收率为99.5%。     

p型碲镉汞液相外延材料Ag掺杂的研究

利用SIMS和变温霍尔测量手段对P型Hg0.77Gd0.23Te液相外延材料的Ag掺杂技术、机理及掺杂碲镉汞材料的性能进行了研究。结果表明采用AgNO3溶液直接浸泡方式对该材料进行掺Ag是成功的，掺杂浓度与被掺杂材料中的汞空位浓度是一致的，掺杂后，P型碲镉汞材料的受主能级比掺杂前有明显的减小，从实验结果可看到掺Ag碲镉汞材料的电学性能在室温下保持稳定。     

Observation and Analysis of Gypsum Particleboard using SEM

The microstructures of gypsum board and gypsum particleboard were observed by SEM. The effects of retarder and waterproof agent on the shape and the average dimension of the gypsum crystal were discussed. The mechanism was investigated as well. Four typical instances, i e, the gypsum crystal shape, the gypsum combined with particles on the particles surface, the gypsum combined with particles on the wood cross section and the gypsum combined with particles inside the wood cell cavity were selected and observed. Furthermore, the agglomeration and cementation mechanism between gypsum and particle were studied.     

HPHT合成钻石中金属包裹体研究

高温高压触媒法简称HPHT法，是一种常用的合成钻石方法。该方法是在压力为5—6个大气压，温度在1500℃～1700℃的条件下，使用金属触媒作为催化剂，石墨原料就会在高温高压下溶解于金属触媒中。当温度降低或压力舱中存在温度梯度时，碳在触媒中达到过饱和状态，就会在种晶上以钻石的形式结晶出来。可以在较短的时间内合成出大颗粒的钻石。     

透明线型低密度聚乙烯专用料助剂配方体系的研制及其性能研究

采用助剂配方后改性的技术方法,研制出用于生产透明线型低密度聚乙烯(LLDPE)膜专用料助剂配方体系ES.ES为有机成核剂/无机成核剂及常规助剂的复配体系.用其改性生产的透明LLDPE专用料的雾度降至13%以下,膜的拉伸强度和断裂伸长率亦有所提高.研究发现,成核剂颗粒的大小及其尺寸分布是影响其增透效果的主要因素.     

Microstructure of Nano-Y203／Cobalt Based ,Alloy Composite Coating byLaser Cladding

Composite coatings made of nano-Y203/cobalt-based alloy and produced by crosscurrent CO2 laser on Ni-based superalloy are introduced. Cross-section or surface of the coatings was examined to reveal their microstructure using optical microscope, SEM, including EDS microanalysis, TEM and XRD. The results show that some equilibrium or non-equilibrium phases, such as γ-C0, Cr23C6, Y203 and ε-Co exist in the coatings. Fine and short dendritic microstructure andcolumnar to equiaxed transition (CET) occurred by adding nano-Y203 particles. With the increasing amount of nano-Y203(1%, mass fraction), fully equiaxed crystallization appeared. These are caused by nano-Y203 particles acting as new nucleation site and rapid solidification of the melt. The results also show that inhomogeneous dispersion of nano-Y203 resultsin the formation of ε-Co phase in the coatings. The sub-microstructure of the clad is stacking fault. The mechanism of theformation of equiaxed grains is also analyzed.     

颗粒增强金属基复合材料的干摩擦性能与磨损机理

颗粒增强金属基复合材料(PMMC5)具有优良的耐磨性，在摩擦磨损领域有着广阔的应用前景。本文评述了近年来关于PMMCs干摩擦磨损行为的研究结果，从材料因素和外部条件两个角度分析了各种因素对材料耐磨性、摩擦系数和配偶件磨损的影响，总结了不同条件下复合材料的磨损机制，并提出了设计摩擦磨损性能优良的PMMCs体系的可能途径。     

卫生陶瓷釉料的质量控制

本阐述了在卫生陶瓷生产中，釉料的颗粒大小、比重、粘度、高温流动性及色釉颜色对产品质量的影响，并介绍其简单的测试、控制方法。