硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景     

锅炉炉管爆破原因分析

对在爆裂的水冷壁管正常管段和鼓包处所取的试样分别进行化学分析、金相检验、硬度测定和高温拉伸试验。分析结果表明，在近烧嘴的炉管长期处于超温工作状态，引起该部位材质严重劣化，高温强度不断下降，当该部位的高温强度低于锅炉炉管对材质所要求的技术条件即会发生爆裂。对炉管的继续使用提出了应急的预防措施。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

Encapsulation of PV modules using ethylene vinyl acetate copolymer as a pottant: A critical review

The primary purpose of this work is to review the literature about what is and is not known about using ethylene vinyl acetate (EVA0 copolymer as the encapsulant (or pottant) material in photovoltaic (PV) modules. Secondary purposes include elucidating the complexity of the encapsulation problem, providing an overview about encapsulation of PV cells and modules, providing a historical overview of the relevant research and development on EVA, summarizing performance losses reported for PV systems deployed since ca. 1981, and summarizing the general problems of polymer stability in a solar environment. We also provide a critical review of aspects of reported work for cases that we believe are important.Failure modes resolved in the early work to establish reliability of deployed modules and the purposes and properties of pottants, are summarized. Typical performance losses in large field-deployed, large-scale systems ranging from 1% to 10% per year are given quantitatively, and qualitative reports of EVA discoloration are summarized with respect to ultraviolet (UV), world-wide location and site dependence.The general stability of polymers and their desirable bulk properties for solar utilization are given. The stabilization formulation for EVA, its effectiveness, and changes in it during degradation are discussed. The degradation mechanisms for the base resin, e.g., unstabilized Elvax 150^TM, and stabilized EVA are indicated for literature dating to the early 1950s, and the role played by unsaturated chromophores is indicated. The limited number of studies relating discoloration and PV cell efficiency are summarized.Observed degradation of EVA or the unstabilized base resin in the laboratory and examples used to measure the degradation are summarized in sections entitled: (1) thermally-induced degradation; (2) photodegradation and photothermal degradation of EVA in different temperature regimes; (3) photobleaching and photodegradation of the UV absorber and cross-linking agent; (4) acetic acid and metal and metal-oxide catalyzed oxidative degradation; and (5) discolaration and PV cell efficiency losses.Processing effects/influences on EVA stability are discussed in sections entitled: (1) EVA raw materials and extruded, uncured films; (2) thermal encapsulation processes; (3) effects of lamination, curing, and curing peroxide on gel content and chromophores formed; and (4) incomplete shielding of curing-generated chromophores. A summary is given for the limited number of accelerated lifetime testing efforts and examples of erroneous service lifetime predictions for EVA are discussed. The known factors that effect the discoloration rate of several EVA formulations are discussed in which the reduction in rate by using UV-absorbing superstrates is a prime example. A summary is given of what is and is not known about EVA degradation mechanisms, degradation from exposures in field-deployed modeules and/or laboratory testing, and factors that contribute to EVA stability or degradation. Finally, conclusions about using Elvax 150 in EVA formulations are summarized, and future prospects for developing the next-generation pottant for encapsulating PV modules are discussed.     

Analysis of the detectivity for triple-layer heterojunction GaSb/GaInAsSb infrared detectors

In this paper, the detectivity is calculated and analyzed with the front-or backside illuminated case for both N-GaSb/p₂-Ga_0.8In_0.2As_0.19Sb_0.81/p₁-Ga_0.9In_0.1As_0.09Sb_0.91 and N₁-GaSb/n₂-Ga_0.9In_0.1As_0.09Sb_0.91/p-Ga_0.8In_0.2As_0.19Sb_0.81 infrared photovoltaic detectors, respectively. The analysis results show that the main absorption appears in the p-type Ga_0.8In_0.2As_0.19Sb_0.81 material with either front- or backside illuminated case for above two structures. In each structure, the carrier concentration obviously affects the detectivity. The carrier concentration in the wide-bandgap material for the isotype heterojunction should be reduced as low as possible to reduce the tunneling rate at the isotype heterointerface. Moreover, the change of the detectivity with the p-side surface recombination velocity for the N₁-n₂-p structure is more sensitive than that with the p₁-side surface recombination velocity for the N-p₂-p₁ structure. In the N-p₂-p₁ structure with the incident light from the p₁-side surface, two-color detection is achieved.     

轴齿轮断齿失效分析

通过对轴齿轮断口形貌、硬度测试及金相组织等试验进行分析表明，齿根处没有进行硬化处理造成齿根处抗疲劳性能不足是导致轴齿轮疲劳断裂的主要原因，另外齿根过渡处倒角过小，且存在纵向刀痕引起了较大应力集中也是导致轴齿轮疲劳断裂的原因。     

Achievement of specificational information usage with true and false feedback in learning a visual relative-mass discrimination task.

Participants' usage of informational variables in learning visual relative-mass discrimination in collisions was tracked by means of PROBIT correlations. Four groups received feedback that was true or accorded with either of three nonspecificational cue variables. A majority in each group adopted the feedback, but several participants defied the false feedback. Unlike in previous research, the fit to data of the relative-mass invariant could not be bettered by post hoc linear combinations of the cues. Discriminability was lower in the use of the invariant. Analytic complexity was rejected as an explanation for discriminability differences. A "smart mechanism" for pickup of the relative-mass invariant was developed as an extension of G. Johansson's (1950/1994) vector model. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Damage mechanisms and failure modes in cross-ply laminates under monotonic tensile loading: The influence of fiber sizing

In this study, the effect of fiber-matrix interphase on the damage modes and failure mechanisms in (0, 90₃), cross-ply graphite-toughened epoxy laminates is investigated. Two material systems (designated as 810 A and 810 O) with the same fiber and same matrix, but with different fiber sizings, were used to study the effect of the interphase. The system designated as 810 A contained an unreacted Bisphenol-A (epoxy) sizing, while a thermoplastic polyvinylpyrrolidone (PVP) sizing was used in the 810 O system. Damage accumulation in the cross-ply laminates under monotonic tensile loading was monitored using edge replication, x-ray radiography, acoustic emission, optical and scanning electron microscopy. Results indicate that the fiber-matrix bond strength is lower in the 810 O system compared to the 810 A system. Transverse matrix cracking initiates at a significantly lower stress level in the 810 O laminate. The 810 O laminates also exhibit longitudinal splitting, while the stronger bonding suppress this damage mode in the 810 A laminates. Numerous local delamination occur on the 0/90 interface at the intersection of 0 and 90 degree ply cracks, in the 810 O laminates. These are absent in the 810 A laminates. The failure modes are also different in the two material systems used in this study. The 810 A laminate exhibits a brittle failure, controlled by the local stress concentration effects near broken fibers. In the 810 O laminates, the presence of longitudinal splits result in the reduction of stress concentration effects near fibe fractures. This results in a global strain controlled failure in the 810 O system. It is concluded that the presence of different fiber sizings result in different damage modes and failure mechanisms in the cross-ply laminates used in this study.Research Associate, Research Assistant, Alexander Giacco Professor and Professor respectively.