Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

预应力多跨混凝土连续板桥在老龙口水利枢纽中的应用评价

文章就预应力多跨混凝土连续板桥在老龙口水利枢纽中的实际应用,通过对河道平槽流量的推求和建桥后桥址处河道过流能力的计算分析,确认该结构形式对河道过平槽流量无大影响。     

沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

流变仪在覆铜板工序中的应用

本文简要叙述利用流变仪对覆铜箔层压板生产工序中的胶液和半固化片参数进行控制,从而更好地保证胶液和 半固化片性状的一致性,以有利于控制板材流胶和品质。     

热镀锌板(卷)工程设计中的环境保护问题

对热镀锌板(卷)的生产工艺、主要生产设备进行了简要介绍，并就其污染源(工序)、生产过程中产生的污染物及其控制措施进行了评述，同时就设计和生产中宜注意的几个环保问题进行了分析。     

Acquisition and pattern recognition of spectrum information of welding metal transfer

With the creation of a pattern recognition system for metal transfer mode, this article has collected five kinds of spectrum signals in gas metal arc welding (MIG, MAG and CO₂) and take them as training samples. These samples have been pretreated by computer, several key characteristic parameters of the spectrum signal have been creatively extracted, and a corresponding recognition function and a minimum-distance-classifier have been constructed. The results show that the pattern recognition of several kinds of metal transfer modes for the metal gas arc welding can be done successfully, and relative important parameters in welding process, such as the frequency of droplet transfer and the approximate diameter of each droplet, can also be obtained.     

Towards implementation of a nickel silicide process for CMOS technologies

In this paper, we review some of the advantages and disadvantages of nickel silicide as a material for the electrical contacts to the source, drain and gate of current and future CMOS devices. We first present some of the limitations imposed on the current cobalt silicide process because of the constant scaling, of the introduction of new substrate geometries (i.e. thin silicon on insulator) and of the modifications to the substrate material (i.e. SiGe). We then discuss the advantages of NiSi and for each of the CoSi₂ limitations, we point out why Ni is believed to be superior from the point of view of material properties, miscibility of phases and formation mechanisms. Discussion follows on the expected limitations of NiSi and some of the possible solutions to palliate these limitations.     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

超声波清洗在贵/廉金属复合材料生产过程的应用研究

本文结合“ODS清洗剂消费淘汰项目”的实施，并对新型超声波清洗机及新型ODS清洗液进行了工艺试验，阐述了超声波清洗技术是贵／廉金属复合材料生产过程中无可替代的清洗技术。     

LD端面抽运掺Yb3+双包层光纤激光器自脉动行为的实验研究

本文对连续波半导体激光器端面抽运的Fabry-Perot腔掺Yb3 双包层光纤激光器的自脉动输出行为进行了研究．发现低Q值腔光纤激光器具有两种形式的自脉动输出，一种是饱和吸收被动调Q产生的自脉冲,另一种是与光纤中的受激Raman散射(SRS)效应相对应的阵发性巨脉冲．通过提高光纤激光器谐振腔的Q值并选择合适的抽运功率，可以有效地减小输出功率的自脉动，获得稳定的连续波激光输出．