用阻容保护装置抑制真空断路器的操作过电压

本文阐述了真空断路器用ＲＣ保护装置的原理。分析了用ＲＣ保护装置保护电力系统及其设备的试验结果。ＲＣ保护装置主要参数的选择。最后，讨论了有关ＲＣ保护装置的一些问题。     

接触网零件振动试验方法探讨

通过对接触网零件用紧固件的耐振动性能进行振后扭矩测试和横向振动采用压力环测试应变进行对比分析，提出了合理的接触网零件耐振动性能试验方法。     

相似理论在真空灭弧室研究和设计中的应用

本文应用相似理论得出,真空灭弧室中电弧运动速度与电流强度成线性关系的相似准则,和极限开断电流与触头直径、开距间的经验公式。认为用小电流模型来研究大电流真空灭弧室是可行的。     

An experimental study on the pumping performance of molecular drag pumps

The pumping performance of molecular drag pumps (MDP) has been investigated experimentally. The experimented MDPs are a disk-type drag pump (DTDP), helical-type drag pump (HTDP) and compound drag pump (CDP), respectively. In the case of the DTDP, spiral channels of a rotor are cut on both upper surface and lower surface of a rotating disk, and the corresponding stator is a planar disk. In the case of the HTDP, the rotor has six rectangular grooves. The CDP consists with the DTDP, at lower part, and with the HTDP, at upper part. The experiments are performed in the outlet pressure range of 0.2–533 Pa. The inlet pressure and compression ratio are measured under the various conditions of outlet pressure and throughputs, and nitrogen is used for the test gas. At the outlet pressure of 0.2 Pa, the ultimate pressure has been reached to 1.0 × 10⁻² Pa for the HTDP, 1.3 × 10⁻⁴ Pa for the DTDP, and 3.6 × 10⁻⁵ Pa for the CDP. The maximum compression ratio of the CDP is much higher than those of the DTDP or HTDP. Consequently, the ultimate pressure of the CDP is the lowest one.     

川中地区上三叠统天然气地球化学特征及成藏过程探讨

川中地区上三叠统是一套自生自储的天然气成藏系统，天然气中甲烷含量为88%～96％，重烃（C2＋）含量一般在6％～9％之间，二氧化碳和硫化氢等非烃气体含量普遍较低；天然气干燥系数（C1／C2＋）为5～15，并且随深度增加而呈现升高的趋势；天然气和凝析油轻烃中的甲基环己烷、庚烷和异庚烷值变化表明天然气主要来源于腐殖型母质；天然气甲烷和乙烷碳同位素分别为-39．00‰～-41．00‰和-25．00‰～-27．00‰，具有典型煤成气特征。川中地区上三叠统烃源岩在燕山期持续沉降埋藏过程中，达到高成熟早期阶段；在喜山期，该地区大约2500m地层的剥蚀，使地层温度和压力大幅度降低，故储层中早期低成熟残余天然气的卸压膨胀作用和水溶气的脱溶作用为晚期天然气聚集成藏提供了重要的气源，同时也使气藏中甲烷碳同位素变轻。     

进口VPSA制氧装置的流程特点及配置

详细介绍了进口的VPSA制氧装置的流程特点、工艺参数及主要设备的配置。实际运转证明 ,该制氧装置具有运行可靠、启动时间短、部分负荷性能优越、负荷转换速度快等优点 ,能满足金隆铜业有限公司的实际生产要求。     

40000m~3/h空分设备主换热器的设计及制造

通过对进口 4 0 0 0 0m3 /h空分设备主换热器进行结构分析及对比模拟计算 ,用国产传热翅片进行设计、采用真空钎焊工艺制造的主换热器 ,经并网运行 ,设计指标优于原空分设备 ,为今后成套大型空分设备板翅式换热器国产化设计、制造创造了条件。     

On the dynamics of non-linear viscoelastic solids with material moduli that depend upon pressure

We investigate the dynamic response, of a generalization of an incompressible Kelvin-Voigt viscoelastic solid, whose viscosity depends on the pressure. Bodies with pressure-dependent material moduli have relevance to numerous technologically significant problems in geomechanics, the mechanics of granular media and powder compaction. We obtain analytical results for creep and recovery phenomena as well as solutions to the propagation of waves in such bodies. We are able to obtain explicit exact solutions that clearly illustrate the marked difference in the response of bodies with pressure-dependent material moduli as opposed to their counterparts whose moduli do not depend on the pressure. We also show that the governing equations for such materials can change type, and that their solutions exhibit singularities and localization.     

变压吸附制氧设备真空风机入口压力低分析和处理

介绍了邯钢动力厂真空变压吸附制氧设备的工艺流程,从切换阀本体、电磁阀及仪表气源等方面分析和总结了真空风机入口压力低引起系统联锁停车故障原因,并介绍了相应的处理措施。