Operational aspects of adsorption air‐conditioner used in diesel locomotive

A locomotive cabin adsorption air‐conditioner has been equipped in #DF4B‐2369 locomotive; and has been successfully run for 2 years. It is powered by waste heat from the exhaust of the diesel engine. The influence on heat transfer is described by the equivalent heat transfer coefficient or thermal resistance of components inside the adsorber. The variation of adsorption capacity is expressed by a non‐equilibrium adsorption function. The dynamic heat transfer process of adsorption air‐conditioning system is treated with the lumped parameter method. Some typical running experimental results are present. The diesel engine rotating speed and locomotive speed influenced on the refrigeration system are discussed. The maximum mean refrigeration power is regarded as an objective function. Based on experiments and theoretical analysis, the running characteristics of the air‐conditioning system are optimized. Some techniques of performance improvement are suggested as well. Copyright © 2006 John Wiley & Sons, Ltd.     

水量还原方法及合理性检查

文中详细地阐述了取河水、井水、水库水、跨流城引(排)水等不同情况进行还原的具体方法步骤。并对水量还原成果提出合理性检查措施。     

Classification of the Uncertainty of Measurements

A discussion is given of questions arising when classifying uncertainties from the point of view of the structure of the measurement process.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

煤层气利用新方案

在介绍煤层气的常规利用方案的基础上，提出了两种利用煤层气的新方案：一是采用变压吸附技术，纯化瓦斯气，将低浓度瓦斯气浓缩为高浓度瓦斯气，加压后成为CNG，用作CNG气源或较远距离城市的天然气气源；二是在第一种方案的基础上，将高浓度瓦斯气全部采用深冷法加以液化，生产LNG，并将LNG运送至更远距离用作LNG加气站、CNG加气站气源。最后还以松藻煤电公司为例，作了新方案的工程预算     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

双室充氮包装机的技术改进

分析了原机型的性能特点和不足之处,介绍了改进方案。     

Interaction of triton X-100 on silica: A relationship between surface characteristics and adsorption isotherms

Adsorption of Triton X-100 on various silica substrates has been investigated. A number of solids, including a natural quartz, this quartz washed with HCl acid and subsequently heated at 1273 K; two aerosils and one Kieselgel silicas were studied. These solids exhibit surface areas in the range of 5 to 430 m² g^?1. All the Triton adsorption isotherms display an S-shape at the adsorption temperatures studied (298 and 308 K). It has been found that the pretreatments of natural quartz (by water washing, impurities removed by acid and/or high temperature calcination) affect considerably the amounts of TX-100 adsorbed. Measurements of surface composition have been made by X-ray photoelectron spectroscopy (XPS) with particular emphasis on the presence of impurities and on the number of OH groups at the surface of the samples. The nature of the surface hydroxyl has also been studied by infrared spectroscopy. Furthermore, the specific number of hydroxyl groups on the surface of the silica samples has been determined by thermogravimetric analysis. Finally an attempt to correlate solid surface characteristics with adsorption isotherms has been developed.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.