面向LTE深度覆盖的PTN接入层网络演进

随着LTE网络覆盖推向深入， PTN接入层网络的承载压力越来越大，本文通过详细分析不同场景的业务带宽需求，结合网络实际，提出PTN接入层网络演进模型，为PTN接入层规划和建设提供了重要的借鉴和参考。     

有关改性沥青混泥土面层施工技术的探讨

沥青路面具有良好的力学强度，在采用机械化施工时也非常方便。所以在现阶段的高等级公路中，沥青路面成为了主要的路面结构。但在实际施工中，改性沥青的施工技术要求非常高，所以对加强改性沥青混泥土施工技术的研究具有非常重要的意义。     

Surface layer condition and the fatigue strength of an AZ91 alloy after ball peening

The present work compares the states of the surface textures and the oscillatory fatigue strengths of specimens made of an AZ91 alloy after turning and dynamic bearing ball peening. It was found that the specimens ball peened at different time have similar surface geometric structure parameters but different strengthening intensity. It was shown that fatigue strength follows greater peening intensity and random and isotropic surface. It was also ascertained that improving (by peening) the condition of the surface layer means enhancing fatigue strength by 20–87% compared with turning.     

Some Effects of Corona Discharge Treatment of Biaxially-Oriented Polypropylene Film

The effects of the unit corona-treatment energy on the contact angle of various liquids, on the surface free energy, on the extent of oxidation of a surface layer, and on the adhesion of acrylic adhesive were studied using a biaxially-oriented polypropylene (BOPP) film. The surface free energy was determined with the van Oss-Chaudhury-Good (VCG) approach as well as with the wettability method. The extent of oxidation of the surface layer of the corona-treated BOPP film was evaluated with X-ray photoelectron spectroscopy. The adhesion strength of joints between the BOPP film and the acrylic adhesive was measured using the 180°-peel test.

In the range of the unit corona-treatment energy up to 1.2 kJ/m², a rapid increase in the surface free energy with the treatment energy is observed. In the range above that value, the surface free energy rises relatively slowly. The extent of oxidation of the surface layer and the adhesion strength of joints between the BOPP film and the acrylic adhesive are approximately in direct proportion to the unit energy of the corona treatment. A five-fold growth of the adhesion strength of the studied joints within the examined range of the treatment energy was found.     

A mathematical model to analyze heat and mass transfer characteristics of a CPL evaporator porous wick

A capillary pumped loop (CPL), because of its high power thermal transport character, has been developed as an attractive system for the thermal discharge of electronic chips with high power loads, especially on spacecrafts. A working fluid having relatively larger heat of evaporation, methanol for example, may transfer significant heat flux. In this paper a new mathematic model is constructed, in which the most important character is the treatment or the unsaturated region of the evaporator porous wick. Numerical simulation of heat and mass transfer in the evaporator porous wick is carried out with a new three‐layer model. The importance of unsaturated layer to simulate the present problem is clear. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(4): 209–218, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20066     

天然钠基膨润土防水毯长效耐久防水工艺

介绍了地下结构工程的常用防水方法，通过工程实例，提出了施作天然纳基膨润土防水毯防水的新工艺，指出该工艺对地下结构工程在长效、耐久防水性能方面具有一定的参考价值。     

原子层沉积制备二氧化钛薄膜及其光催化性能研究

采用原子层沉积方法在K9玻璃上制备出TiO₂薄膜,利用XRD、SEM、AFM、分光光度计和紫外-可见光谱仪表征了不同沉积温度下薄膜的物相结构、光学性能和光催化性能。结果表明：25℃和120℃下制备的TiO₂薄膜为无定形态结构,210℃和300℃下可获得锐钛矿结构;随着沉积温度的升高,薄膜的晶粒尺寸变大,表面粗糙度增加,透射率降低,光催化性能增强;300℃下制备的TiO₂薄膜(2mm*2mm)经过12h的紫外可见光照射,甲基橙溶液的降解率可达47.16%,通过增加样品表面积可明显提高对甲基橙溶液的降解率。     

6061/AZ31B/6061对称复合板的组织与力学性能研究

本文在理论分析与模拟计算的基础上,通过热轧制备了6061 Al/AZ31B Mg/6061Al对称复合板,并对其组织结构和力学性能进行了研究。首先通过经典复合板理论计算得到了复合板中6061Al的最佳包覆率,再通过有限元方法模拟得到了复合板的最佳压下率。依据理论分析和仿真计算得到的铝的最佳包覆率和复合板的最佳压下率,对6061 Al/AZ31B Mg/6061Al复合板进行组坯,并在不同轧制温度、不同压下率和不同退火时间下进行了轧制实验,最后对实验得到的复合板进行了微观组织、拉伸性能和能谱分析。结果表明,在复合板的复合界面处的镁层中发现了再结晶晶粒,且界面上形成了由Mg17Al12和Mg2Al3组成的金属间化合物;随着轧制压下率的增大,6061 Al/AZ31B Mg/6061Al复合板的拉伸强度、延伸率和界面扩散厚度显著增大;随着轧制温度的升高,复合板的拉伸强度、延伸率和界面扩散厚度也增大;而随着退火时间的增加,复合板的拉伸强度降低,但界面扩散厚度增加。     

反应温度及时间对奥氏体不锈钢渗铬层组织结构的影响

利用固体粉末包埋技术对316H奥氏体不锈钢进行了1090℃保温0.5～20 h和750～1150℃保温10 h的化学热处理,研究了不同工艺参数对渗铬层组织结构和耐磨性的影响。通过光学金相显微镜(OM),扫描电镜(SEM),能谱仪(EDS)以及X射线衍射仪(XRD)等分析手段,研究了保温时间和反应温度对渗铬层的微观组织结构的影响规律,使用摩擦磨损试验机研究了不同工艺参数对渗铬层耐磨性的影响。结果表明:反应温度对渗铬层的厚度影响显著,在同一温度下进行渗铬,渗铬层的厚度与渗铬时间呈抛物线关系;渗铬层主要由Cr_(23)C_6、Cr_2C和α-Fe-Cr固溶体组成,在渗铬过程中,首先在试样表面形成碳铬化物层,随着反应温度提高或保温时间延长,在碳铬化合物层下会生成α-Fe-Cr固溶体层,进一步提高反应温度和保温时间,碳铬化合物层逐渐消失。渗铬后试样的耐磨性明显提高,且在相同温度下渗铬,保温时间短的耐磨性好;相同保温时间,反应温度低的耐磨性好。