蒸发式冷凝在制冷工艺上的应用

分析对比制冷工艺中几种冷凝方式，指出发展蒸发式冷凝技术对制冷系统节能的重要意义；通过分析蒸发式冷凝的换热机理，在试验和实践的基础上讨论了影响蒸发式冷凝器性能的几个重要因素。     

Z900MCM综述

介绍了Z900 MCM设计和布局,可控塌陷芯片连接(C4)工艺在Z900 MCM组装中的应用。从设计上通过加入垂直电感器及去耦电容器减小其噪声。通过基板测试和功能测试,剔除有缺陷的基板和芯片。Z900 MCM采用先进的MCM—D技术和MCM返工及冷却技术。Z900 MCM平均无故障时间高达40年。     

灯泡贯流式机组发电机冷却装置技术改造方式的探讨

灯泡贯流式发电机组直径小,转速低,发电机的通风冷却是一个难点。通过对京南、马骝滩、石面坦及南津渡等水电站的发电机运行过程中出现的温升过高,定子线棒绝缘受损等问题的分析,提出了解决的措施与改进方案,并对灯泡贯流式机组冷却系统的设计提出了建议,可供参考和借鉴。     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

低温液体冷却循环器的研究与开发

根据低温生物、生化实验研究和产品小试时应用低温条件的特点，提出机械制冷的冷却循环器，讨论了工作原理和制冷量计算，对其制冷系统和温度控制进行介绍。     

内燃机车临时补水设备的设计与应用

针对内燃机车“途中缺水”故障 ,设计并安装临时补水设备 ,解决了电化区段临时补水的问题 ,满足了内燃机车“不停车、不停机”即可补水的要求。     

轧后穿水冷却工艺对棒材组织性能的影响

针对轧机产量提高后冷床冷却能力不足的问题 ,研制开发了棒材轧后穿水冷却技术。通过对小规格 2 0MnSiV热轧带肋钢筋进行轧后穿水冷却 ,钢材上冷床温度降低了 90～ 110℃ ,提高了产品质量 ,改善了各项力学性能 ,抗拉强度平均提高了 3 5～ 40MPa ,钢材性能合格率由 97.5 %提高到了 99.6% ,解决了冷床冷却能力不足、制约生产的瓶颈问题。     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。     

机械过冷的制冷系统在汽车空调中的应用

由于很多汽车空调采用斜盘式压缩机，有利于采用机械过冷的制冷系统，来增加汽车空调的制冷量、提高制冷效率。本文的主要目的是通过对系统工质的流量分配、空调制冷量和性能系数(COP)与中间压力之间的变化关系的研究，来研究机械过冷在汽车空调中应用的可行性。     

可再生能源在空调制冷中的应用

针对目前压缩式制冷技术带来的能源短缺和环境污染问题，介绍了几种可再生能源在空调制冷中的应用技术，如地道风供冷、地源热泵系统、太阳能空调制冷，分析了可再生能源用于空调制冷的特点及发展现状，并对其应用前景做了展望。