改善多层住宅供暖设计的几项措施

提出了将水平干管敷设于屋面以解决上供下回系统在建筑层高较低时，水平干管影响室内美观及排气阀浮球不易检修等矛盾的几种设计方案。介绍了几项改善管网运行效果的措施。     

The TDCPR Management Mode of Engineering Equipment

The Three Gorges Project is a very large project,and its structure is very complex.Interna-tional advanced engineering equipment is broadly used.The state of equipment running directly influ-ences project building qualities and limited time.According to the factud conditions of the Three Gor-ges Project,the characteristics of engineering equipment are analyzed.At the same time ,some theories about equipment management are induced ,and the TDCPR management mode of engineering equip-ment of the Three Gorges Project is put forwared in order to gain the aim of managing and using equip-ment well and speeding up the project construction.     

ATM协议的测试研究及其应用

协议一致性测试和互操作性测试是保证不同厂商的ＡＴＭ产品和服务实现完全的互通的重要技术手段，本文分析了ＡＴＭ协议的测试需求，提出了适合的测试结构和测试描述技术，并结合适配层协议ＣＰＡＡＬ５讨论了协议集成测试系统ＰＴＴＳ在ＡＴＭ协议测试中的应用。     

多棒高功率固体激光器动态模匹配研究

采用光学矩阵分析了多元热透镜谐振腔内模式的动态匹配特征,给出了平平腔参数调整的关系式,实验结果与理论分析相符,并在两棒连续Nd:YAG系统上得到0W～530W功率范围的稳定输出.     

分子振动态及其跃迁的激光相干控制

讨论了激光合成相干叠加态的原理及其性质 ,针对 XY2 型分子 ,证明了合成局域模振动的可行性 ,然后给出相干叠加态的跃迁几率特征 ,发现它仍表现出相干的特性 ,对之进行分析研究表明 ,分子的振动态具有可控性 ,态跃迁几率具有可控性。     

Measurements of Stress Intensity Factors of an Interface Crack Under Mixed Mode Loading

The optical method of caustics has been utilised to measure both the stress intensity factor for a crack lying along the interface of an aluminium/epoxy bimaterial specimen, and the mode mixity arising from the difference in the elastic properties across the interface. Measurements were carried out by using a novel modification to the method whereby caustics are produced and measured from both sides of the specimen, so compensating automatically for the distortion induced in the specimen due to misaligned loading fixtures. A flat reflective surface across the interface was obtained by adhering a reflective coating to the specimen. Verification that this coating does not affect measurement accuracy was obtained by comparing stress intensity factors measured from coated and uncoated monolithic aluminium specimens where good agreement was found to exist between both measurements.     

油气两相压降数值试井模型及其典型曲线的规律

提出油气两相流动压降试井数字模型的数值解法，用此解法对均质油藏中油气两相流动试井的规律进行了研究，根据实例计算结果，分析油气两相流下典型压降试井曲线的特征，以及油、气的初始饱和度分布，两相黏度比，饱和度梯度、相对渗透率关系对试井曲线的影响和相应的作用机理，首次发现气体的存在会使油气两相试井的压力导数曲线表现出类似于单相流双重介质试井的压力导数曲线的“下凹”特征。     

抗高温磨损高铬铸铁的研究

经Mo、B、V、Ti合金化和RE变质处理的高铬铸铁，具有优良的抗高温磨损性能和强韧性，用于制造筛分高温烧结矿的振动筛筛板，使用寿命比ZG30Cr18Mn12Si2N耐热钢筛板提高2倍以上。多元高铬铸铁筛板制造工艺简单，成本低，值得在筛分领域推广使用。     

耦合腔行波管慢波结构的工作模式及其特性

耦合腔行波管慢波结构可工作于三种不同模式：正常模、简并模和反向模。应用改进的等效电路法计算了正常模腔通带和槽通带。求得的简并模耦合槽张角与实验值相符。最后讨论了反向模耦合腔行波管诱人的特点。     

自升式平台深水化改造的新模式及其可行性分析

针对我国现有自升式平台存在的不能满足深水域勘探开发的要求以及造价过高等问题,提出一种自升式平台深水化改造新模式——分体坐底自升式平台,在基本不改变原有平台结构的基础上,通过增加可沉浮平台下体,使作业水深增加50m以上,而造价比同工作水深的常规自升式平台低得多。文章介绍了该分体坐底自升式平台的结构方案、作业工况及操作程序,分析了该平台的技术可行性和经济可行性,并提出了深入研究和具体实施需要解决的问题。