In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Surface structural change of ZnO-coated LiNi0.5Mn1.5O4 spinel as 5 V cathode materials at elevated temperatures

LiNi_0.5Mn_1.5O₄ powder was synthesized via sol-gel method and coated with ZnO in order to test the electrochemical cyclability of the material as a cathode for the secondary Li battery in the 5 V range at 55 °C. The ZnO-coated LiNi_0.5Mn_1.5O₄ powder nearly maintained its initial capacity of 137 mA h g⁻¹ after 50 cycles whereas the uncoated powder was able to retain no more than 10% of the initial capacity after 30 cycles. TEM analysis of the cycled cathodes suggests that the formation of the graphitic surface phase, hindering the Li migration, may be responsible for the rapid capacity loss of the uncoated material while no such phase was observed on the surface of the ZnO coated LiNi_0.5Mn_1.5O₄ powder.     

埋地管道三层PE外覆盖层及其检测方法研究

文章介绍了埋地管道三层PE外覆盖层系统的构造参数和性能特点,论述了两种用于埋地钢质管道外覆盖层状况检测的方法,一种是多频管中电流法,另一种是DCVG/CIPS组合检测技术。分别介绍了两种方法的工作原理、操作方法和设备,并结合工程实例进行了说明。这些方法和设备可分别或同时用于管道不开挖检测防腐层破损点的位置以及漏点大小。     

纳米涂层的研究现状与展望

简述了纳米表面涂层制备工艺的研究现状，分析了气相沉积、热喷涂、电刷镀、化学镀和电沉积等不同工艺在制备纳米表面层中的应用情况。介绍了纳米涂层在超硬耐磨、耐腐蚀、耐高温热稳定性等方面研究的新进展，并对纳米涂层的应用范围和领域作了展望。     

核壳乳液聚合中甲基丙烯酸用量对印花制品的影响

采用核壳乳液聚合法合成涂料印花粘合剂，考察了甲基丙烯酸(MAC)用量的改变对印花产品的牢度和色光的影响：在核中，当MAC的用量分别为0．0g，0．2g，0．4g，0．6g时，干摩牢度分别为25，2．5 ，3,0，3．5，色光由暗变亮；在壳中当MAC的用量分别为0．0g，0.2g，0．4g，0．6g时，干摩牢度分别为2.5，2．5 ，3．0，3．5，色光变亮，对得色量和鲜艳度影响不大。     

聚氨酯干法涂层的应用

介绍了涂层织物的特点及聚氨酯在涂层整理中的作用,并对干法直接涂层工艺进行了探讨.     

烷基烷氧基硅烷的合成方法及其在涂料中的应用

介绍了烷基烷氧基硅烷的合成方法(包括烷基的引入方法和烷氧基的形成方法)、近几年来在涂料中的应用及其结构与性能的关系。     

以国标GB1.7为指导编制“变流器包装”企业标准

介绍了某企业在变流器包装的设计和制定其企业标准的过程中执行ＧＢ１．７（标准工作导则）的情况，论述了在充分考虑产品特点和流通环境条件下，企标增补的内容，这些内容是对变流器包装有关标准的深化和创新。新企标不仅注重标准深度，而且考虑标准广度方面的拓展，代表了当前较好的生产水平，可作为生产过程中控制质量，评价和检验质量的依据。     

真空铸造高强度C／Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过１０００ＭＰａ的高强度Ｃ／Ｍｇ复合材料。将Ｔ３００纤维经Ｃ－Ｓｉ－Ｏ梯度涂层处理后单向排布于型腔内，在真空下注入ＺＭ—５合金液，凝固后即得Ｃ／Ｍｇ复合材料零件或试样。试样的抗拉强度在纤维体积分数为０．３５时达１０５０ＭＰａ。本文讨论Ｃ－Ｓｉ－Ｏ梯度涂层对获得高强度复合材料的作用。     

Membrane Packaging System to Permit Safe Hydration of Freeze-Dried Contents with Impure Water

We tested the feasibility of using polymer membranes for a self-hydrating packaging system to reconstitute freeze-dried foods using nonpurified water. Several commercial membranes were screened according to (1) hydration rate, (2) water permeability, (3) passage of microorganisms, (4) salt rejection, and (5) strength. The most promising membranes were used for developing and testing prototype packaging systems. A feasible self-contained rehydration system was a nylon-6 polyamide membrane that rehydrated the freeze-dried food within 30 min while passage of microorganisms was prevented. The temperature was 37°C, and the food contained 0.5g/5g of a low molecular weight solute (salt). Such self-contained membrane rehydration systems must be designed to accommodate expected environmental conditions such as temperature, relative humidity, and nature of the product.