拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

熔融温度对PP中成核剂的异相成核作用的影响

用DSC研究了熔融温度对不同类型成核剂成核PP的异相成核作用的稳定性的影响。观察到随熔融温度提高，纯PP的成核作用稳定，降温结晶温度基本不变。而有机磷酸盐类成核剂成核PP的结果温度比纯PP的高，而且异相成核作用受熔融温度的影响也很小。但山梨醇类成核剂成核PP的异相成核作用随熔融温度提高，结晶温度逐步降低明显，表明其异相成核作用对热不稳定。     

Photostability of polyetherurethaneureas

Polyetherurethaneureas (PEUUs) were synthesised from polyethylene-glycols (PEGs) of molecular weight 400, 600 and 1000, 4,4′-diphenylmethanediisocyanate (MDI) and aliphatic diamine chain extenders, 1,3-propanediamine (PDA) and 1,6-hexanediamine (HDA). Polymer films were irradiated with 365 nm light at 293 K and the effects of polyether soft segment length and urea hard segment on photo-oxidative stability were studied by following the variation in weight-average molecular weight (M _w), gel formation and stress-strain properties. Changes in ultraviolet and infrared spectroscopy were monitored on photo-oxidation and hydroperoxide content determined. The soft segment length was increased by increasing the molecular weight of PEG from 400 to 1000 and hard segment structure was changed by variation of diamine. It was noted that the structure of urea and polyether soft segment length plays an important role in photostability of PEUUs. PDA chain extended PEUUs were more stable than HDA chain extended PEUUs.     

聚丙烯共混表面改性剂的研究

由不同链长的甲基丙烯酸长链醇酯。少量改性剂与聚丙烯共混，能大幅增加聚丙烯表面润湿性与粘接性，而拉伸强度与熔点却变化不大。通过ＥＳＣＡ与接触角分析，发现极性基团大表面富集，添加不同改性剂使材料表面富集的极性基浓度与粘接强度产生差异。     

Surface designing of polypropylene by critical monitoring of the grafting conditions

The grafting of acrylic acid onto electron beam‐irradiated polypropylene was carried out using preirradiation method. The stability of peroxy radicals was investigated by electron spin resonance. It was found that the decay of peroxy radicals is much faster at 70°C than at 40°C and ambient temperature. The grafting has been observed to be strongly dependent on the monomer dilution in the reaction medium. The grafting was ascertained by attenuated total reflectance (ATR). The distribution of grafts across the samples was monitored by infrared microscopy. It was found that the graft management is considerably influenced by composition of the grafting medium. The grafting involving pure monomer leads to the surface enrichment with the polyacrylic acid chains. The samples grafted in pure monomer led to much lower contact angles as compared to the diluted monomer solution. The swelling of the grafted samples also showed a trend that was governed by the graft management. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 546–553, 2006     

环氧乙烷合成乙二醇的研究进展

介绍了环氧乙烷合成乙二醇的主要生产方法，包括以壳牌、联碳化学公司以及Halcon—SD公司为代表的环氧乙烷直接水合法，环氧乙烷催化水合法和碳酸乙烯酯法，后两种乙二醇生产方法是目前国内外研究开发的热点。催化剂体系是催化水合法工艺的关键，重点介绍了国内外各主要公司对催化剂体系的研究进展及使用效果；碳酸乙烯酯法分为乙二醇和碳酸二甲酯联产法以及碳酸乙烯酯水解法，详细介绍了国内外各主要公司对该技术的研究进展，包括工艺流程、催化剂体系等方面。将3种乙二醇生产方法进行技术经济比较，结果表明，催化水合法和碳酸乙烯酯法在原料消耗和能耗方面占优势。并对我国乙二醇生产工艺技术提出建议。     

聚丙烯表面改性及与涂料的粘结

讨论了聚丙烯制品喷涂着色的优点及影响聚丙烯制品与涂料之间粘结强度的各种因素。综述和评价了对聚丙烯进行表面改性的必要性及各种表面改性方法。     

Effect of material and process parameters on the mechanical properties of unidirectional and multidirectional flax/polypropylene composites

Unidirectional (UD) and multidirectional (MD) flax/polypropylene composites were studied. Flax with varying retting degree and boiled flax was used as reinforcement for the UD composites and unmodified and maleic acid anhydride modified polypropylene (MAA-PP) was used as matrix. Multidirectional flax/polypropylene composites were manufactured on laboratory scale and on pilot scale. They were made from needle-punched hybrid flax/PP non-wovens. Normally retted flax as well as boiled flax was used. For the specimens made on pilot scale, a third kind of flax, namely bleached flax was also studied. The influence of different process times and temperatures on the mechanical properties of the composites was analysed. Generally, the composites have adequate good mechanical properties. The unidirectional composites of boiled flax combined with MAA-PP show the best mechanical properties. Contrary to the UD composites, flax treatment did not lead to the expected property improvements for MD composites.     

新型聚氨酯固-固相变储能材料的组成与热性能的关系

利用差示扫描量热仪、傅里叶红外光谱仪、广角X射线衍射仪研究了一种新型的以聚乙二醇为软段的聚氨酯相变储能材料。结果表明，当软段含量低于90％（质量分数，下同）时，即使温度高于聚乙二醇的熔点，此类材料仍不会熔化成液体，而表现出一种固-固相变行为。该聚氨酯储能材料相变焓较大，相变温度适中，且随着软段含量的减少，材料相变焓和相变温度呈递减趋势。其相变过程实质是聚氨酯软段聚乙二醇由结晶固态转变为无定形固态的过程。     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry