导静电乳液胶粘剂的研制

用多元乳液共聚法制备了用于粘贴导静电PVC地板胶粘剂,加入乙炔碳黑赋予乳液胶粘剂导静电性能。研究了影响胶接强度和初粘力的主要因素,确定m(VAc)/m(BA+VAc)较合适比为1∶3;研究了乳化剂和交联单体对乳液性能的影响,研究得出,适量加入AA和HMAM可以减少乳化剂的用量,提高乳液的性能;考查了影响导静电性能的因素,研究表明,导静电性能由乙炔碳黑决定,其加入量越大,导静电性能越好。得到的导静电乳液胶粘剂胶接强度达到0.51MPa以上,导静电可达到7.2×103Ω,两项指标均超过国家标准。     

数码彩色喷墨打印纸用涂料的研究进展

较详细地介绍了数码彩色喷墨打印纸用涂料中各个组成部分的选择及其常用颜料、胶粘剂和其它助剂的特点及性质 ,指出将纳米技术和环保技术应用到涂料中是涂料发展的必然趋势。以聚乙烯醇和复合胶粘剂为粘结剂 ,微孔型二氧化硅为颜料制备喷墨打印纸专用涂料是当前的研究热点。     

一种高吸水性新型高分子复合肥载体的研究

研究了一种新型高吸水率和高吸收利用率的高分子复合肥 ,它以脲甲醛缩聚物作为载体 ,以聚乙烯醇缩甲醛作为吸水功能体 ,以磷酸钙、氯化钾作为包覆体 ,以硬质聚氨酯泡沫作为支撑体并采用发泡工艺制备。     

亚乙基双硬脂酰胺改性淀粉胶的研究

本文采用亚乙基双硬脂酰胺对淀粉胶进行了改性，研究结果表明，亚乙基双硬脂酰胺是热法淀粉胶的有效而廉价的改性剂，对淀粉胶的存性能和使用性能具有综合改性效果。     

环氧树脂-聚丙烯酸酯乳液型复合薄膜粘合剂

本文主要叙述了环氧-丙烯酸酯聚合乳液的合成,以及该乳液粘合剂的配制;讨论了该乳液粘合剂的粘合性能及耐水、耐溶剂性能。     

PFF与PUF热稳定性及燃烧性能研究

制备了酚醛泡沫和聚氨酯泡沫，并研究了酚醛硬泡与聚氨酯硬泡的热稳定性及燃烧性能。结果表明：和聚氨酯泡沫比较，酚醛泡沫的热失重小，热释放速率和热释放总量低。因此酚醛泡沫的热稳定性和阻燃性能明显优于聚氨酯泡沫。     

玉米淀粉胶粘剂的改性研究

以玉米淀粉为主要原料 ,通过预糊化、氧化、加碱糊化进行化学改性 ,并加入稳定剂可制备固含量高、贮存稳定性好 ,具有一定初粘力和透明性的改性淀粉胶粘剂。本论文主要研究了改性玉米淀粉胶粘剂的主要成分配比及工艺条件对产品性能的影响。结果表明 :淀粉氧化前是否进行预糊化处理、氧化剂的用量、体系pH值、加碱糊化时碱液用量、稳定剂的种类和用量等对改性玉米淀粉胶粘剂性能影响较大。     

Structure and properties of regenerated cellulose films coated with polyurethane–nitrolignin graft‐IPNs coating

A regenerated cellulose film (RC) was coated with a graft‐IPNs coating, which was composed of castor oil‐based polyurethane and 2.8 wt % nitrolignin (NL), to obtain water‐resistant films. The effects of NCO/OH molar ratio and different polyols, such as 1,4‐butanediol (BDO) and trimethanol propane (TMP), on the structure and properties of the coated RC films were investigated. With an increase of the NCO/OH molar ratio, the tensile strength of the coated films increased, but the water resistivity and size contraction hardly changed. The coated films with TMP exhibited the higher breaking elongation at 1.5 of the NCO/OH molar ratio, while those with BDO have more excellent tensile strength, water resistivity, and dimensional stability. The coated films with the graft‐IPNs coating exhibited superior water resistivity and dimensional stability. The light transmittance of the coated films was more excellent than that of the RC film. Moreover, the results from the IR and electron probe microanalysis (EPMA) showed that the chemical bonding occurred between cellulose and coating, and the introduction of NL plays an important role in the enhancement of the interface adhesion of the coated films. Atomic force microscopy (AFM) depicted the flat and dense surface of the coated films, which restricted the water vapor penetration and the size contraction, resulting in the enhancement of water resistivity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1799–1806, 2002     

Durability of Adhesion Between Metals and Polymers

Adequate adhesion between metals and polymers is primarily the result of chemical bonds in the boundary layer. This region, however, is subject to degradation by moisture. Three modes of deterioration are observed. The first is a largely reversible weakening effect in the polymer layer near the metal oxide surface. The structure of this layer differs from that of the bulk and is influenced by the chemical and physical properties of the surface. The second is a slow transformation of the oxide by hydration and a diffusion of oxide constituents into the polymer. This process is irreversible and is influenced by the state of the surface and chemical properties of the polymer. The third is a fast deterioration of the oxide by primary corrosion usually initiating at an unprotected edge but occasionally arising within the body of a joint.     

高柔韧性聚氨酯丙烯酸酯的合成及应用

选用不同结构的多元醇作骨架，合成一系列高性能的聚氨酯丙烯酸树脂，并通过对聚氨酯丙烯酸树脂性能的对比研究，发现以聚丁二烯二元醇为骨架的聚氨酯丙烯酸酯树脂具有极佳的柔韧性和优异的低温耐曲折性。