���������͵�����������ķ�����Ӧ��

本文提供了计算凝析油当量气体体积的方法，并用于凝析气藏的凝析油含量，凝析油和干气地质储量的计算。     

烟用香料配制的气相色谱法质量控制研究

采用气相色谱法对香料房卷烟用料液中的溶剂及水分进行检测,分析测定其中的水分、乙醇、丙二醇、山梨醇等的含量,通过对香料房每批配制料液的抽检,可以跟踪料液配制的准确性,保证卷烟产品质量,该方法操作简单、准确性高、重现性好。     

On collaborative content distribution using multi-message gossip

We study epidemic schemes in the context of collaborative data delivery. In this context, multiple chunks of data reside at different nodes, and the challenge is to simultaneously deliver all chunks to all nodes.     

A Mass Transport Model for Drying Wood under Isothermal Conditions

Mass transport in wood during drying can have different mechanisms at different periods of drying. Depending on the current moisture content (MC) and the structure of the wood, the driving forces for the mass transport are essentially different. Above the fiber saturation point (FSP), the lumens are partially saturated and the transport of liquid (free) water occurs as a consequence of capillary action. On the other hand, below the FSP, bound water within the cell walls is conveyed by diffusion, and water vapor in the lumens moves under influence of pressures gradient. Based on these considerations, a unified model is presented that takes into account the transport of the different moisture phases. Simulation of the drying of a Norway spruce sample at 50°C from about 135 to 7% MC is carried out using the finite element method (FEM). Comparison between the simulated average MC and the experimental observations obtained from X-ray computed tomography (CT) shows reasonable agreement. Possible simplifications in the model are briefly discussed as well as some aspects of the numerical implementation. Finally, the influence of absolute permeability on the average MC is studied.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

Hydrolytic stability and protective properties of polyurethane oligomers based on polyester/ether/polyols

The present study deals with effect of the type and chemical character of incorporated polyester/polyether blocks on the hydrolytic stability of crosslinked polyurethane oligomers. Diffusion parameters of the investigated polyurethane oligomers, giving information concerning chemical changes taking place in neutral, basic and acidic aqueous environments, have also been determined.     

水性聚氨酯电导率与聚沉值的研究

研究了软（硬）段含羧基的水性阴离子纳米聚氨酯体系的n(NCO)/n(OH)比值，COOH的质量分类，反离子各类，合成方法与电导率关系及产生的原因；探讨了该体系的n(NCO)/n(OH)值，COOH的质量分数，合成方法与临界聚沉值（Cc.c)的关系和规律。并分析，比较了软（硬）段含羧基的水性阴离子聚氨酯体系电导率与Cc.c二者关系，得出了随COOH的质量分数升高，二者变化相同，随n(NCO)/n(OH)比值升高,二者变化相反的结论。     

戊二醛含量测定方法的改进

对戊二醛测定方法进行改进 ,采用酸度计判定终点的方法代替用肉眼观察指示剂变色来判定终点。改进后的方法平均偏差为 0 .0 4,标准偏差为 0 .0 2。并且在正常情况下 (试样无色 ,含量≥ 1% ) ,改进前后的测试方法的数据结果基本一致。而当试样含量≤ 1%或试样有色时 ,则测试结果相差很大。     

In situ polyurethane/silica composite formation via a sol‐gel process

Polyurethane acrylate anionomer (PUAA)/silica composite gels were prepared by the sol‐gel reaction of tetraethoxysilane (TEOS) and methacryloxypropyl trimethoxysilane (MPTS) incorporated to PUAA gels by using a swelling method. The formation and structure of composites were confirmed by FTIR, X‐ray diffraction, and SEM. As a result, we found that silica components in composites are located within the ionic domains of their gels and interacted with PUAA via hydrogen bonding. This drastically enhanced the mechanical properties of the composites. Mechanical properties are also improved by MPTS, because MPTS improves the dispersibility and adhesion of silica components in PUAA/silica composite gels. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2327–2334, 2002     

Development and characterization of magnetorheological polymer gels

Magnetorheological materials have been used in many applications in recent years. To develop new materials, polyurethane and silicone polymer gels were investigated. Rheology is qualitatively controlled for each system by controlling the concentration of reactants and diluents. The resulting polymers have solid, gel, or liquid states, depending on the crosslinking and dilution. The gels were characterized through kinetic analysis. Differential scanning calorimetry (DSC) was used with analysis methods to find the kinetic properties for diluted and undiluted polyurethane systems. Heat of reaction, order of reaction, preexponential constant, and activation energy were obtained from the experimental DSC data. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2733–2742, 2002