自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

A Finite Element Computational Method for Gas Hydrate. Part I: Theory

A finite element scheme is presented to model the dissociation of gas hydrates in porous media by hot water injection. We show a complete derivation of the finite element formulation, including the associated mass and energy conservation equations capable of performing transient analysis of both conductive and convective heat transfer for gas and liquid flow in porous media. The scheme also includes the latent heat effect to accommodate the change of phase due to melting of hydrate. In the companion paper, Part II, this method is successfully applied to hydrate reservoirs.     

Effect of organic dopants on electrodeposition and characteristics of polyaniline under the varying influence of H2SO4 and HClO4 electrolyte media

Electrodeposition of conducting polyaniline (Pani) was made under potentiostatic condition at pH 1.0 in different electrolyte media (H₂SO₄ and HClO₄) in the absence and presence of two organic dopants, disodium salts of naphthalene-1,5-disulphonic acid (NSA) and of catechol-3,5-disulphonic acid (CSA). The rate and yield of Pani deposition were dependent on the acid medium and the dopant employed. NSA in H₂SO₄ caused an increase in rate and yield but CSA decrease when compared to the rate and yield of H₂SO₄ alone. In HClO₄ medium, both the dopants showed a decrease. With regard to DC electrical conductivity, both the dopants exhibited an enhancement in H₂SO₄ medium but NSA a decline in HClO₄. Characterisation of the electrosynthesised polymer samples by various instrumental techniques (cyclic voltammetric: CV, FTIR, UV-Visible: UV-Vis, EPR, XRD, TGA and DTG methods) revealed that between the two acid media, H₂SO₄ was the better one. Further, it enlightened the role of two organic dopants in relation to the acid media. The advantageous role of NSA in H₂SO₄ had origin on its molecular characteristics such as non-polarity, larger π-electron cloud etc., while CSA could not perform such a role because of its easily oxidisable hydroxyl groups. In HClO₄, however, both the dopants could play only an unfavourable role owing to its greater polarity and oxidizing power than H₂SO₄.     

H.323同步控制实现研究

提出并实现了一种H.323多媒体通信系统音视频同步控制算法,算法以正常语音播放为基准,利用H.263码流语法信息,通过调整视频播放帧率实现媒体间同步, 不增加通信冗余度。实际测试结果表明,算法有效地提高了多媒体通信系统音视频媒体同步性能和多媒体的感知服务质量,并已应用于实际多媒体通信系统。     

无限水介质中爆炸冲击波压力计算公式辨析

对无限水介质中爆炸的冲击减压力计算公式在实际应用中应如何选用进行了辨析，提出了不同条件下推荐使用的公式。     

管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

P／MCs新型复合材料制备、结构及阻尼性能

采用特殊的渗流法所制备的新型Ｐ／ＭＣｓ复合材料，由高分子聚合物与蜂窝状铝架组成，它具有优异的阻尼性能，并简述了结构对阻尼的影响     

Significance of fluid regime in biological filtration

A dispersed flow model previously developed to study substrate utilization in unsaturated media was experimentally verified and its practical application was considered. For this purpose, measurements were made using tap water and a synthetic feed solution. The importance of the change in fluid regime as regards to the simultaneous transport and reaction within biological filters were demonstrated. The effect of drop formation and the breakage of liquid jets inside the filters on substrate utilization was also shown.     

含多孔物质硝胺发射药的温感特性

研究了多孔物质对于硝胺发射药在不同初温下的燃面调节作用，由于多孔物质的孔结构及其与基体界面状况的改变，使发射药低温燃面增大，而高温燃面减小，这有利于降低燃速温度系数．     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.