粗粒土渗透变形机制浅析

对砂卵砾石的渗透变形的形成条件进行了简要分析，在此基础上对渗透变形的形式进行了简要评价，并提出了渗透变形临界坡降的计算方法。     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

宽带放大器可靠性问题浅析

叙述了国产高频宽带放大器的质量和可靠性现状，详细介绍了这类产品的质量一致性检验、可靠性摸底试验和现场使用过程中出现的可靠性问题，用统计的方法得出了可靠性特征量，通过对失效样品的失效分析，总结出宽带放大器主要的失效模式和失效机理，并提出了消除和减少失效、提高宽带放大器可靠性的措施和建议。     

智能机理与软计算

随着计算机科学技术,特别是人工智能及其它相关学科的发展,关于人脑智能机理的研究引起越来越多的注意。与此同时、出现了关于软计算的研究.旨在研制出高机器智商系统(High Maehine Intelli-gene。Qt,,:sen:、产tom)[,〕。本文将初步探索智能机理与软计算两者间的关系以及把它们结合起来解决问题的可能性和途径。     

抗震结构变形能力可靠度的时程分析方法

采用可靠指标β来度量抗震结构可靠度．取结构失效准则为：地震作用下结构层间位移响应超越结构层间位移能力限值．将时程分析方法与ＪＣ方法结合，建立了计算抗震结构变形能力可靠指标β的时程分析方法．     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

水溶性防氧化剂在SMT用印制板上的应用

水溶性的防氧化剂是一种有机可焊性保护剂。其方法是在印制板完全阻焊、字符层的印刷，并经电检之后，通过表面浸渍在裸铜的贴片位或通孔内形成一种耐热性的有机可焊性膜层。这种有机、可焊、耐热的膜层，膜厚可达0.3-0.5mm，其分解的温度可达约300℃，传统的印制板的热风整平法亦无法满足QFP愈来愈密集的需求，同时也无法满足SMD表面平整度的要求，更无法适应PCB薄型化生产。烷基苯并咪唑的OSP法能弥补这项缺陷，因而在PCB业乃至SMT产业中得到了广泛的应用。     

控制棒驱动机构常温通风均匀性试验研究（续篇）

本文叙述控制棒驱动机构在常温通风均匀性方面的试验。通过平顶型堆顶结构和球面型堆顶结构通风均匀性试验的比较,找出通风的阻力、风速和不均匀系数间的规律。