钻探用变量泥浆泵曲轴强度的计算

随着钻探业的不断发展 ,日趋需要大功率的泥浆泵 ,文章介绍了大变量泥浆泵机组中曲轴的设计。     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.     

土壤源热泵取热的实验研究

通过广泛分析国内外对土壤源热泵实验研究的现状,建立了可以模拟多个地区、多种运行工况的土壤源热泵沙箱实验台,并进行了绝热边界工况短期内取热的实验研究。     

液化天然气供气站的工艺设计

〗LNG供气站的设计核心是工艺设计，设计中应注意以下几点：正确处理技术先进性与经济合理性的关系，综合权衡设置费与运营费的比例，力求项目全寿命费用最低；大多数城市LNG供气站均利用空气气化LNG，单罐容积为100 m³的真空压力式储罐广泛用于储存量为1200 m³以下的LNG供气站；为正确设置储罐安全阀的开启压力和排放压力，必须根据储罐的最高工作压力按照规范正确确定储罐的设计压力；储罐上2套独立的液位计和高、低限报警自动切断装置可确保储罐安全运行；空温式气化器的气化能力按用气城市高峰小时计算流量的1.3~1.5倍确定，为便于自然化霜应设置2套空温式气化器切换使用；空温式气化器出口串接水浴式加热器可提高冬季或雨天出口天然气温度，保护碳钢管道并降低供销差；LNG储罐区应设置围堰，消防用水量为喷淋与水枪用水量之和。最后建议，必须尽快颁布国家LNG设计规范，以提高我国的LNG设计水平。     

Optimization by random search with jumps

We give a random optimization (RO) algorithm to optimize a real‐valued function of n real variables. During the optimization process, interpolation points are examined to follow valleys, and jumps to new starting points are executed to avoid numerous iterations in local minima. Convergence with probability one to the global minimum of a function is proved. The proposed RO method is a simple, derivative‐free and computationally moderate algorithm, with excellent performance compared to other RO methods. Seven functions, which are commonly used to test the performance of optimization methods, are used to evaluate the performance of the RO algorithm given here. Copyright © 2004 John Wiley & Sons, Ltd.     

马尾松木材中性脱脂工艺的研究

采用全因素试验法，对马尾松木材进行过热乙醇溶液脱脂处理，以获取马尾松木材高效脱脂工艺技术。试验结果显示：（1）脱脂温度对马尾松松脂溶出量的影响极显著，且溶出量随着脱脂温度的升高而增大；（2）脱脂时间对马尾松松脂溶出量的影响极显著，且溶出量随着脱脂时间的延长呈先增大后减小的趋势；（3）脱脂浴比对马尾松松脂溶出量的影响极显著，且溶出量随着脱脂浴比的延长呈先增大后减小的趋势；（4）利用过热乙醇溶液对马尾松木材进行脱脂，其最佳工艺是脱脂时间为130℃、脱脂时间为8h、浴比1：8。     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Control of discrete time nonlinear systems with a time-varying structure

In this paper, we present a control methodology for a class of discrete time nonlinear systems that depend on a possibly exogenous scheduling variable. This class of systems consists of an interpolation of nonlinear dynamic equations in strict feedback form, and it may represent systems with a time-varying nonlinear structure. Moreover, this class of systems is able to represent some cases of gain scheduling control, Takagi-Sugeno fuzzy systems, as well as input-output realizations of nonlinear systems which are approximated via localized linearizations. We present two control theorems, one using what we call a “global” approach (akin to traditional backstepping), and a “local” approach, our main result, where backstepping is again used but the control law is an interpolation of local control terms. An aircraft wing rock regulation problem with varying angle of attack is used to illustrate and compare the two approaches.     

高层地下室底板混凝土施工的裂缝控制

以德益花园写字公寓楼地下室底板205m厚混凝土的施工工程为例，坚持预防为主的原则，采取了一系列温控技术措施，有效地防止或控制了温度裂缝(收缩裂缝)的产生，确保了混凝土的施工质量。